Whirlpool Washer Sensors

Videos!

Your Price

$35.67

Whirlpool Washer Dryer Thermostat Internal Bias

★★★★★

35 Reviews

PartSelect Number PS11746740

Manufacturer Part Number WP8577274

This dryer thermistor is a genuine replacement component designed to monitor and regulate internal temperature in Whirlpool dryers. Mounted on the blower housing, it plays a critical role in controlling the heating element by adjusting resistance as temperatures rise, signaling the control board to maintain safe and efficient drying conditions. A malfunctioning thermistor can result in symptoms such as no heat, overheating, premature cycle termination, or failure to start. It may also trigger fault codes like F-22, F-23, E1, or E2. Replacing the thermistor restores proper temperature regulation, protects the appliance from damage, and improves drying performance. Installation should be performed with the dryer unplugged and may require basic tools.

Fixes these symptoms

Not Heating
Too hot
Touchpad does not respond
See more...

Installation Instructions

Steven from East Norriton, PA

Dryer overheated, blew out thermal fuse

I started to repair this and got busy and ended up calling a repair service -- that was the first time. They repaired it for over $200 and said the cause was bad venting. I fixed the vent before using the fixed dryer but it blew again. So I ordered these parts and replaced them myself for a lot of savings. However, the dryer still overheated. Through lots of testing I found the root cause the repairman missed: The heating element had gotten so hot that the assembly holding it warped, hitting the element and shorting it. So a new element is on order. I still needed the parts I ordered here but the overall repair ended up more complicated and expensive. I was disappointed a paid repair person left without further diagnosis. If he had unplugged the vent and checked the heat on the exhaust vent (as I ended up doing) it would have been obvious more than a new thermal fuse/thermistor was necessary. Instead I wasted over $200 on his visit. So my advice is if you're at all handy, repair this yourself. The dryer has a service manual inside the front toe board that walks you through most diagnostics and tests. However, it took a little more than that for me to discover the heating element problem. This was a very dangerous situation that could have easily led to a fire, yet not found by a trained technician! Read more...

Videos!

Your Price

$36.72

Whirlpool Washer Sensor

★★★★★

10 Reviews

PartSelect Number PS11749664

Manufacturer Part Number WPW10178988

This rotary position sensor is a genuine OEM part for your washing machine. It helps to ensure the load of clothing stays balanced during the wash cycle. Customers have rated this repair as easy. To complete this repair, you will need an Allen wrench, 3/8 inch socket, and a screwdriver. The repair will involved turning off the power and water supply, and tilting the washer on its front to access the sensor.

Fixes these symptoms

Spinning Issues
Will not agitate
Will Not Start
See more...

Installation Instructions

Edgardo from SALEM, OR

F51 error code

Pretty easy! Just follow this link on how to fix the problem:

https://www.youtube.com/watch?v=_-Hg8rLGiKQ

The hardest part on fixing this is trying to move the washer out of its place so I can tilt it to see underneath the washer where the repair would be. Read more...

Videos!

Your Price

$33.54

Whirlpool Washer Temperature Sensor

★★★★★

6 Reviews

PartSelect Number PS11755214

Manufacturer Part Number WPW10467289

This part regulates the temperature of the water in the tub. The sensor is located in the heating element.

Fixes these symptoms

No hot or cold water
Will not drain
Will Not Start
See more...

Installation Instructions

william from VIRGINIA BCH, VA

Replacing the heat sensor following an F-24 Error Notice.

I followed your repair video explicitly, simple fix. However, one should
be careful when disconnecting the two prong electrical connector from
the heat sensor. the two black wires can pull free easily. In that case, the
rear of the female plastic wired connector must be extracted to allow the two black wires to be "pushed" into the narrow slot which displaces the
wire insulation and allows for a good electrical connection. If a punch tool is not available a pair of needle nose pliers works. Also, observe
the orientation slots on both the male andfemale connectors - they
connect one way only! I set the washer on it's face while effecting this
repair to better see what I was doing (eyesight not as good as it used to be). Thanks for the timely support! Read more...

Your Price

$54.01

Whirlpool Washer Sensor

PartSelect Number PS11731237

Manufacturer Part Number W10853313

Your Price

$48.95

Whirlpool Washer Sensor

PartSelect Number PS12349236

Manufacturer Part Number W11208385

Your Price

$58.36

Whirlpool Washer Sensor

★★★★★

1 Review

PartSelect Number PS11751018

Manufacturer Part Number WPW10247389

Introducing the genuine OEM Sensor from Whirlpool, designed for optimal performance in select models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef appliances. This sensor is specifically crafted to monitor coins inserted into the coin box of commercial laundry machines, ensuring accurate operation. Do remember that while parts may share similar appearance, variations in size and shape can occur. Therefore, ensure you have the correct part number for your specific appliance model before order placement. Prior to installation, ensure to unplug the appliance and wear work gloves for enhanced safety. Trust Whirlpool for components that are both functional and durable.