Murray Parts
Popular Murray Parts
Your Price
$6.21
In Stock
Murray Bearing
HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
PartSelect Number PS9006914
Manufacturer Part Number 532009040
The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft. Over time, the part may become worn and damaged, which you will notice if you experience a squealing or grinding sound from the wheel in question, or you notice the wheel is sloppy on the shaft.
You will need a hammer and punch to complete this repair, which most of our customers rated as easy. Make sure you tap the new bearing into place evenly inside the tire rim.
Installation Instructions
robert from EUREKA, CA
transaxle rotated forward on 2015 Husqvarna YT42DXLS
2015 Husqvarna YT42DXLS. Both transaxle support struts broke causing the transaxle rotated forward and shear transaxle mounting bracket. The transaxle was not damaged. All 3 parts required replacement. There are some good youtube videos to watch to show how to complete the repair. HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
Your Price
$37.15
In Stock
Murray Grass Catcher Frame
PartSelect Number PS9988561
Manufacturer Part Number 647-04271-0637
Installation Instructions
Anthony from OLIVEHILL, TN
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Read more...
Your Price
$3.99
On Order
Murray Ring Klip Number T5304-75
PartSelect Number PS9143890
Manufacturer Part Number 812000029
The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle.
This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.
Your Price
$3.99
In Stock
Murray Cap Axle Black 1 50 x 1 00
PartSelect Number PS9007667
Manufacturer Part Number 532104757
This genuine black cap axle, also sometimes known as the dust cap, is around 2 inches in diamater and sold individually. Comprised of plastic, it is designed to keep debris out of the hub and axle of your lawn mower or garden tractor. Over time, your dust cap may become damaged or lost due to wear and tear. If this happens, dirt and debris can freely enter the axle and hub, causing damage.
This is an easy repair to make and does not require any tools. Just look for the cap axle on the rim of the wheel to make your repair.
Installation Instructions
Anthony from OLIVEHILL, TN
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Read more...
Your Price
$3.99
On Order
Murray Washer 25/32 x 1-1/4 x 16 Ga.
PartSelect Number PS9008998
Manufacturer Part Number 532121749
This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending on the equipment, its general function is to spread the load under a bolt. Ensure you consult your owners manual or check your model number to confirm this is the washer you need for your equipment.
This part will need to be replaced when your existing one is worn or damaged. It is an easy repair according to our customers, and does not require any special tools.
Installation Instructions
Frederick from BINGHAMTON, NY
Your Price
$3.99
In Stock
Murray Clip, Hairpin
PartSelect Number PS9007536
Manufacturer Part Number 532003146
This hairpin clip, also known as a cotter pin, is a genuine OEM sourced part used to secure rotating components together in various outdoor power equipment. It is made of steel and is approximately 1.5 inches long. The clip acts as a fastener to prevent the moving parts from loosening and falling off during usage. The clip is vulnerable to corrosion and general wear over time. However, it can also fail prematurely due to overloading and excessive stress. A damaged hairpin clip will result in misalignment of parts, accidental disassembly, increased friction and wear, and potential harm to the user. Remove the faulty pin and align the new one with the insertion points. Ensure that the pin is securely fitted in its appropriate slot and compress the ends to prevent it from dislodging.
Your Price
$48.56
In Stock
Murray Lawn Tractor Mandrel Assembly
PartSelect Number PS12087499
Manufacturer Part Number 587819701
Your Price
$16.18
In Stock
Murray Blade Mower
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact driver, ..... and you know the rest. Read more...
PartSelect Number PS9286056
Manufacturer Part Number 532138971
This replacement blade is supplied directly from the original equipment manufacturer for use with Craftsman riding lawn mowers and garden tractors. It is secured under the deck to cut the grass, over time the blade may become dull or damaged causing irregular cutting patterns. Inspect your blades periodically and replace them as needed to maintain a clean cut lawn. It is a high-quality component which is made of durable steel and it is sold individually.
Installation Instructions
Trace from LISLE, IL
Needed to replace the bent blades on my riding mower.
- Made the mower safe to work on the blades (remove spark plug wires, etc.)- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact driver, ..... and you know the rest. Read more...
Your Price
$4.99
In Stock
Murray Pin, Shear, 1-3/4
PartSelect Number PS9999468
Manufacturer Part Number 703063
Shear Pins are designed to break off in order to prevent further damage to your machine. Because they are designed to break, we recommend having a few spares on hand. This part is made of metal, is silver, is not part of a kit or assembly, and is sold individually.
A Shear Pin will break when you hit a large chunk or ice or other debris. Once it is broken, it will need to be replaced. You will need pliers to complete this repair.
Customers rate this repair as Easy.
Your Price
$15.90
In Stock
Murray Blade, 22"
Make Bend adjustments for the Handle to fit. Read more...
PartSelect Number PS9017810
Manufacturer Part Number 532406713
This blade is sourced directly from the manufacturer for use in Craftsman and Husqvarna lawn mowers. The blade is the part of the mower that is responsible for cutting and mulching the grass. It is 22" long, made of black metal, is not part of a kit or assembly, and is sold individually.
If you hit a hard object, you may bend the blade, causing a vibration. You may also have problems with the grass being cut as the blade dulls over time. If the blade is bent, damaged, or worn, it needs to be replaced. You will need a socket set to complete this repair.
Customers rate this repair as Easy.
Fixes these symptoms
- Mower blade does not cut
- See more...
Installation Instructions
Charles from Memphis, TN
I had to buy Troy-Bilt parts to adjust for a Murray Lawn Mower
Grind off 1/4" of each end of the 22" blade to fit 21' Mower.Make Bend adjustments for the Handle to fit. Read more...
Related Murray Parts
- Murray Blower Parts
- Murray Lawn Mower Parts
- Murray Lawn Tractor Accessories Parts
- Murray Lawn Tractor Parts
- Murray Snow Blower Parts
- Murray String Trimmer Parts
Popular Murray Models
Below are the most popular Murray models we have. Enter your model number in the search box to find your model.
- 7800583 7800583 - Walk Behind Mowers
- ZTS7500 Zts 7500, 26hp Bands W/50-Inchmower Deck
- ZTS7500 19hp Bands W/42" Mower Deck
- ZTS7500 Zts 7500, 21hp Bands W/42-Inchmower Deck
- ZTS7500 22hp Bands W/50" Mower Deck
- ZTS7500 20hp Koh W/44" Mower Deck
- ZTS7500 Zts 7500, 26hp Kohler W/50-Inchmower Deck
- ZTS7500 20hp Koh W/44" Mower Deck
- ZTS7500 19hp Bands W/42" Mower Deck
- ZTS7500 22hp Bands W/50" Mower Deck
- ZTS7500 24hp Bands W/50" Mower Deck
- ZTS7500 24hp Bands W/50" Mower Deck
- ZTS7500 24hp Bands W/50" Mower Deck
- ZTS7500 24hp Bands W/50" Mower Deck
- ZTS7500 20hp Koh W/44" Mower Deck
- ZTS7500 20hp Koh W/44" Mower Deck
- ZTS7500 20hp Koh W/44" Mower Deck
- ZTS7500 20hp Koh W/44" Mower Deck
- 21595x8A 21" Walk-Behind Mower
- 21595X8A 21595x8a - Walk Behind Mowers
