Genuine OEM Tiller Parts – PartSelect.com

Your Price

$3.99

Tiller Clevis Pin

★★★★★

2 Reviews

PartSelect Number PS9009427

Manufacturer Part Number 532132673

This clevis pin is an OEM replacement part that is compatible with various makes and models of tiller and is sold as an individual part. The purpose of this pin is to snap or break under a certain amount of pressure if your tiller is jammed, to protect the more valuable components of your tiller. Measuring at approximately 2-inches long and made of high-quality metal, replacing this pin should only require pliers to swap out the old pin for the new.

Fuel Tank Assembly W/Fuel Lines Incl. 29 – Part Number: 753-06797

Your Price

$22.11

Tiller Fuel Tank Assembly W/Fuel Lines Incl. 29

★★★★★

1 Review

PartSelect Number PS11812933

Manufacturer Part Number 753-06797

The fuel tank assembly is responsible for storing and supplying fuel to the engine in lawn and outdoor power equipment. It includes the tank, fuel cap, and fuel lines. The fuel tank assembly will fail if the tank develops cracks or leaks, or if the fuel lines can become clogged. When the fuel tank assembly fails, you will notice fuel leakage, restricted fuel supply, stalling, difficulties starting and overall lower performance. Before beginning any repairs, first drain any remaining fuel from the tank for your safety. Disconnect the fuel lines from the tank and remove the fuel tank from the equipment. Position the new tank on to the mounting holes and secure it in place. Connect the fuel lines to the engine and vent to complete your repair.

Installation Instructions

Robert from ORANGE, CA

One of the two fuel lines cracked and leaking

Removed the 6 screws holding the red plastic cover, tank, and the old fuel lines from the carburetor. Placed the new tank in the sunlight for a few minutes to soften the new fuel lines. Then attached the new lines to the carburetor and replaced the cover Read more...

Extension Control Cable Reverse (1430mm) – Part Number: A203121

Your Price

$40.96

Tiller Extension Control Cable Reverse (1430mm)

PartSelect Number PS16723235

Manufacturer Part Number A203121

Your Price

$3.99

Tiller Clip, Hairpin

PartSelect Number PS9007536

Manufacturer Part Number 532003146

This hairpin clip, also known as a cotter pin, is a genuine OEM sourced part used to secure rotating components together in various outdoor power equipment. It is made of steel and is approximately 1.5 inches long. The clip acts as a fastener to prevent the moving parts from loosening and falling off during usage. The clip is vulnerable to corrosion and general wear over time. However, it can also fail prematurely due to overloading and excessive stress. A damaged hairpin clip will result in misalignment of parts, accidental disassembly, increased friction and wear, and potential harm to the user. Remove the faulty pin and align the new one with the insertion points. Ensure that the pin is securely fitted in its appropriate slot and compress the ends to prevent it from dislodging.

Your Price

$11.83

Tiller Throttle Cable

★★★★★

1 Review

PartSelect Number PS10009725

Manufacturer Part Number 753-06831

Your Price

$18.86

Tiller Cbl/Cltch T

PartSelect Number PS11971272

Manufacturer Part Number 583731701

Your Price

$3.99

Tiller Air Filter

★★★★★

2 Reviews

PartSelect Number PS9117898

Manufacturer Part Number 753-05996

Wheel, 13 Inch, Right – Part Number: A200809

Your Price

$143.84

Tiller Wheel, 13 Inch, Right

PartSelect Number PS10041115

Manufacturer Part Number A200809

This is a genuine OEM supplied replacement wheel that is specially manufactured for use on Powermate and Southland rear tine tillers. It is the right wheel that keeps the unit mobile for easy transportation. This high-quality wheel is sold individually, it consists of a metal rim and a durable rubber tire. Please note the left wheel and the hardware to secure these parts are all sold separately.

Installation Instructions

Willie from BLYTHEWOOD, SC

tiller tires lost air pressure both tires during tilling in gardening. .Try to replace innertube. No dice. Ordered wheel assembly completed.

After receiving wheel assembly, 5 minutes installation wheels installed. Back in business! Read more...

Cable Barrel Holder – Part Number: 946-0605

Your Price

$4.54

Tiller Cable Barrel Holder

★★★★★

1 Review

PartSelect Number PS9167431

Manufacturer Part Number 946-0605

This cable barrel holder is a genuine OEM part that is designed for use with tillers and snow throwers. Sold as an individual part, this holder measures approximately 1-inch in length and is used to secure the clutch control handle and cable together. This holder is made of durable plastic and can replace the old holder by simply removing it, inserting the cable into the new holder, and tightening it until it is locked in place.?