Genuine OEM Snow Blower Parts

Your Price

$6.15

Snow Blower Lock Nut

PartSelect Number PS16381786

Manufacturer Part Number 596039201

Snow Blower Shear Pin – Part Number: 738-04124A

Your Price

$3.99

Snow Blower Shear Pin

PartSelect Number PS9110822

Manufacturer Part Number 738-04124A

This individually sold shear pin is an OEM replacement that is most typically used in snowblowers but can also be used within snowblower attachments for lawn tractors. Its main uses are connecting the auger and auger shaft, which are the rotating blades, and to protect more valuable components such as the transmission.If the snow is causing excessive force or there is a jam within the auger and connected housing,it will cause the shear pin to snap, effectively stopping the rotation of the auger, while the auger shaft and gears will continue turning. If the shear pin snaps, snow will simply build up on the outside of the auger housing, since the auger will no longer spin. This shear pin has a .25-inch diameter, and 1.5-inch length and is sold individually. Most augers have a pin on each side, so you may need to purchase more than one, and it is also recommended that you carry spare pins in case of a future breakage.

Clip-Hold Down (Nylon) – Part Number: 1724869099

Your Price

$12.52

Snow Blower Clip-hold Down (nylon)

★★★★★

1 Review

PartSelect Number PS9903766

Manufacturer Part Number 1724869099

Hold-down clips, also known as retaining, locking or fastening clips, are designed to secure and fasten specific parts within equipment, and the use depends on the type and model. This hold down clip is used to secure the chute of various models of snowblowers, and is sold as an individual OEM part, without any securing hardware. Made of nylon, this clip secures to the chute with two screws and two washers. If you notice a wobbly or insecure chute resulting in excessive vibrations from the chute, check to make sure the clip is in-place before inspecting it for damage and ordering a replacement. To replace this clip, you will need to gain access to the chute, with either a screwdriver or wrench, and once you can access it, it is as simple as unscrewing the old clip and installing the new clip and rest of the assembly.

Snow Blower Primer Bulb – Part Number: 66-7460

Your Price

$6.57

Snow Blower Primer Bulb

★★★★★

1 Review

PartSelect Number PS9056413

Manufacturer Part Number 66-7460

This manufacturer-certified Primer Bulb is a black rubber part which comes individually sold. It is used to pump fuel from the fuel tank to the carburetor to start the engine. Installation is rated as "Easy" by customers, and will require a screwdriver and pliers. The part attaches to the primer assembly. If the bulb breaks due to wear/fatigue/damage you will see fuel leaking, and the part should be replaced. Refer to your make, model and diagrams to ensure this is the correct part.

Snow Blower Shear Bolt – Part Number: 51001500

Your Price

$4.99

Snow Blower Shear Bolt

PartSelect Number PS9002923

Manufacturer Part Number 51001500

This OEM-verified shear bolt, measuring 2-1/8 inches in length and 5/16 inches in diameter, is designed to break under excessive force to protect your lawn equipment by absorbing the impact. Specifically, it allows the augers of your machine to stop while the shaft and gear case continue to rotate. To check if the shear bolt is broken, inspect it for fractures or missing pieces. You might notice that the shaft of your machine is rotating normally but the augers are not moving with it. It is important to address a damaged shear bolt promptly to avoid costly repairs or equipment failure. To remove the shear bolt from your machine, use a wrench or socket to turn it counterclockwise. As this replacement part is sold individually, it is strongly recommended that you keep spare bolts on hand in the event that they break.

Installation Instructions

Dennis from WESTFIELD, MA

Switch return spring broken

Removed panel, unsrew switch assy. Remove electric connector s, reverse process to reinstall Read more...

Your Price

$8.66

Snow Blower Cable

PartSelect Number PS8800615

Manufacturer Part Number 06900504

Snow Blower Lock Nut – Part Number: 3296-42

Your Price

$5.95

Snow Blower Lock Nut

PartSelect Number PS8953555

Manufacturer Part Number 3296-42

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.