Husky Snow Blower Parts

Popular Husky Snow Blower Parts

Your Price
$3.99
   In Stock
Husky Snow Blower Shear Pin, .25
PartSelect Number PS9110822
Manufacturer Part Number 738-04124A
This individually sold shear pin is an OEM replacement that is most typically used in snowblowers but can also be used within snowblower attachments for lawn tractors. Its main uses are connecting the auger and auger shaft, which are the rotating blades, and to protect more valuable components such as the transmission.If the snow is causing excessive force or there is a jam within the auger and connected housing,it will cause the shear pin to snap, effectively stopping the rotation of the auger, while the auger shaft and gears will continue turning. If the shear pin snaps, snow will simply build up on the outside of the auger housing, since the auger will no longer spin. This shear pin has a .25-inch diameter, and 1.5-inch length and is sold individually. Most augers have a pin on each side, so you may need to purchase more than one, and it is also recommended that you carry spare pins in case of a future breakage.
Your Price
$20.78
   In Stock
Husky Snow Blower Speed Selector Cable
PartSelect Number PS9166871
Manufacturer Part Number 946-04396A
This speed selector cable is sourced from the original manufacturer and consists of a cable enclosed in an outer protective casing. It connects the control panel to the transmission/drive system of the snow blower, allowing you to adjust and select the speed at which the snow blower moves. When you adjust the speed on the control panel, the cable is activated, and it engages with the transmission to control the snowblower. The speed selector cable can fail over time due to various reasons including fraying from use and exposure to harsh conditions, corrosion, or inadequate lubrication, which causes it to become stiff. If the cable is faulty, your equipment will be unable to move, or stuck at one speed, and the control panel may be unresponsive. Disconnect the faulty cable and route the new cable through the same path. Connect the cable to the control panel and transmission, and secure it with the appropriate fasteners.
Your Price
$2.99
   Special Order
Husky Snow Blower Cotter Pin
PartSelect Number PS10003638
Manufacturer Part Number 714-04040
Your Price
$3.99
   In Stock
Husky Snow Blower Carburetor Gasket Plate
PartSelect Number PS17016727
Manufacturer Part Number 751P11897B
Carburetor Gasket Plate
Your Price
$4.49
   In Stock
Husky Snow Blower Chute Flange Keeper
★★★★★
★★★★★
1 Review
PartSelect Number PS10005747
Manufacturer Part Number 731-0851A
This chute flange keeper is sourced from the original equipment manufacturer for use in snowblowers. The plastic keeper allows the snowblower chute to pivot, and secures the flange that connects the chute to the blower frame and holds it in place during use. Over time the flange keeper can break or fall off, which causes the chute to dislodge or shift from its position. If you notice that debris is discharged in the wrong direction, and you have difficulties adjusting the chute then this is a sign that the flange keeper is no longer functioning as it should. Clean the chute flange and surrounding area before placing the new keeper on. Use a pair of pliers to align the the holes on the flange keeper with the holes on the chute and lock it in place.
Installation Instructions
Jason from PEABODY, MA
Carburetor rebuild
I can’t complete this easy repair because partselect sent the wrong part and has not responded to customer service requests. Please contact me- jtandree@gmail.com Read more...
Your Price
$5.97
   In Stock
Husky Snow Blower Steering Triggers
★★★★★
★★★★★
1 Review
PartSelect Number PS9104626
Manufacturer Part Number 731-04954
Your Price
$4.07
   In Stock
Husky Snow Blower Carriage Bolt, 5/16-18 x .75
PartSelect Number PS10001568
Manufacturer Part Number 710-0451
This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the nut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.
Your Price
$4.10
   In Stock
Husky Snow Blower Nut, Flange Lock, 5/16-18, Grf
PartSelect Number PS9092936
Manufacturer Part Number 712-04063
This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant to loosening when threaded on a bolt. It has a variety of applications and is used in multiple locations on most models. Please refer to your owners manual to determine the exact location. While made of durable metal, the ends can round off from improper use of a wrench or socket. Depending on the location, this part may also become worn through regular use of your machine. It should be replaced when visibly cracked, worn or damaged. To complete this repair, you will need a wrench or socket, and a torque wrench. Ensure you torque the bolt according to the manufacturer recommendations. Customers rate this repair as Easy.
Your Price
$4.24
   In Stock
Husky Snow Blower Nut, Flange Lock, 3/8-16, Grf
PartSelect Number PS9095080
Manufacturer Part Number 712-04065
Designed for use in various models of lawn and garden equipment, this part is not sold as part of a kit or assembly. It is made of metal, is gold in color, and is sold individually. This part may also be called a Flange Lock. This nut is designed to lock in place, preventing vibrations and other parts coming loose. This nut may be located in multiple locations on your machine, refer to your owners manual to determine if this is the correct part. You will need a wrench or socket set and a torque wrench to complete this repair. You should only torque the nut to the manufacturer recommendation, no tighter. You will need to replace this part when it is worn or damaged. While this part can wear through regular use, it is most commonly damaged through improper use of a wrench or socket. Customers describe this repair as Easy.
Installation Instructions
Carl from DECATUR, TX
Seized bearing and spacer on bolt shaft for idler pulley
Unfortunately I couldn’t find the spacer on the Internet, so I ended up going to the hardware store and buying multiple sizes of spacers and bearings to complete the install. I ended up using a steel spacer with shoulder and two bearings. Way overkill, but worth the three dollars. Read more...
Your Price
$4.43
   In Stock
Husky Snow Blower Chute Flange Keeper
PartSelect Number PS9104771
Manufacturer Part Number 731-04869A
The chute flange keeper is a genuine OEM replacement part that secures the chute flange on snowblowers. The keeper is made of plastic and fits onto the metal piece, known as the flange, that connects the chute to the blower frame and holds it in place during use. Over time the flange keeper may wear down or fall off and cause the chute flange to fall out of alignment. If you notice that you have difficulties adjusting the direction of the chute and you hear rattling during use, then this is a sign that the flange keeper is no longer properly attached. Before positioning the new keeper, clear off any dirt or debris in the area. Use a pair of pliers to fit the keeper on and align the holes on the flange keeper with the holes on the chute before securing it.

Husky Snow Blower Appliance Types

Related Husky Snow Blower Parts

Popular Husky Snow Blower Models

Below are the most popular Husky Snow Blower models we have. Enter your model number in the search box to find your model.