Snow Blower Hardware

Snow Blower Bow Tie Cotter Pin Sourced directly from the manufacturer, this replacement part is designed to secure otherwise loose parts in place, allowing the machine to operate properly. This Bow Tie Cotter Pin is not part of a kit or assembly and is sold individually. It is silver, made of metal, and is used in a variety of models for various purposes. This part needs to be replaced when it is broken or damaged, or the threads have become stripped. Depending on their location, this part is known to wear with regular use. You will need a wrench or socket set to complete this repair. Customers rate this repair as Easy.

Snow Blower Locking Flange Nut This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant to loosening when threaded on a bolt. It has a variety of applications and is used in multiple locations on most models. Please refer to your owners manual to determine the exact location. While made of durable metal, the ends can round off from improper use of a wrench or socket. Depending on the location, this part may also become worn through regular use of your machine. It should be replaced when visibly cracked, worn or damaged. To complete this repair, you will need a wrench or socket, and a torque wrench. Ensure you torque the bolt according to the manufacturer recommendations. Customers rate this repair as Easy.

Snow Blower Carriage Bolt This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the nut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.

Snow Blower Lawn Mower Ring Clip

★★★★★

★★★★★

1 Review

The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle. This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.

Snow Blower Lawn Tractor Bolt 596039401

Snow Blower Shear Bolt And Nut This shear bolt and nut, also known as the shear bolt assembly, is sourced from the original manufacturer, and it is guaranteed to fit your snowblower. Each assembly includes one metal shear bolt and one metal nut, located at the connection point between the auger and gearbox/shaft. It is a safety mechanism designed to protect the snowblower auger from damage caused by sudden stops or excessive resistance. When the auger encounters a blockage or excessive load the shear bolt will break thereby preventing more severe damage to the gearbox. Once the bolt is sheared, it will need to be replaced. The bolt will also need to be replaced if it is bent or worn down, as a faulty shear bolt can result in damage to the auger, gearbox, and motor, as well as reduced equipment ability to throw snow, and increased safety risks. Use a socket or wrench to unthread the nut and remove the broken shear bolt. Align the new shear bolt with the mounting hole and secure it with the new nut. Note that this is a common repair and it is best to have several spare shear bolts and nuts on hand.

Snow Blower Lock Nut

Snow Blower Shear Bolt This OEM-verified shear bolt, measuring 2-1/8 inches in length and 5/16 inches in diameter, is designed to break under excessive force to protect your lawn equipment by absorbing the impact. Specifically, it allows the augers of your machine to stop while the shaft and gear case continue to rotate. To check if the shear bolt is broken, inspect it for fractures or missing pieces. You might notice that the shaft of your machine is rotating normally but the augers are not moving with it. It is important to address a damaged shear bolt promptly to avoid costly repairs or equipment failure. To remove the shear bolt from your machine, use a wrench or socket to turn it counterclockwise. As this replacement part is sold individually, it is strongly recommended that you keep spare bolts on hand in the event that they break.

Snow Blower Clip-hold Down (nylon)

★★★★★

★★★★★

1 Review

Hold-down clips, also known as retaining, locking or fastening clips, are designed to secure and fasten specific parts within equipment, and the use depends on the type and model. This hold down clip is used to secure the chute of various models of snowblowers, and is sold as an individual OEM part, without any securing hardware. Made of nylon, this clip secures to the chute with two screws and two washers. If you notice a wobbly or insecure chute resulting in excessive vibrations from the chute, check to make sure the clip is in-place before inspecting it for damage and ordering a replacement. To replace this clip, you will need to gain access to the chute, with either a screwdriver or wrench, and once you can access it, it is as simple as unscrewing the old clip and installing the new clip and rest of the assembly.

Snow Blower Carriage Bolt