Trash Compactor Parts
Popular Trash Compactor Parts
Your Price
$58.57
In Stock
Trash Compactor Drive Gear Kit
Removed the drive gear and the washer.
Used a nail to drive out the pin for the smaller drive gear kit. Removed and replaced with new, used new pin to lock it on to the shaft. Changed out the bearings and washers on one powerscrew, put chain back on. Then was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Greased chain, gear drive and powerscrew. Put all covers back on with the screws. Pushed button it worked. Read more...
PartSelect Number PS398589
Manufacturer Part Number 882699
This is the drive gear kit for the ram that compacts the trash inside your compactor. If your compactor ram is getting stuck, there is excess noise during its cycle, or if your compactor does not stop at the end of its cycle, the driving gear may be the issue. The gear is white, plastic and approximately 4.5 inches in diameter. This drive gear kit includes both gears, pin spring, retaining clip (c-ring), ram stop, ram cam, and instructions. Make sure to disconnect the power to your trash compactor before beginning the repair.
Fixes these symptoms
- Compactor ram gets stuck
- Doesn’t stop at end of compacting cycle
- Drawer is hard to open and or close
- See more...
Installation Instructions
Asbjorn from The Woodlands, TX
Compactor stuck in lower position
Moved the compactor out from under cabinet and unplugged the powercable.Laid compactor over on its side Removed the top (4 screws) and base plate (3 screws) as well as the coverplate for the motor(3 screws)Found that large drive was broken in half. Used two screwdrivers to start split ring then pliers to pull it off the rest of the way.Removed the drive gear and the washer.
Used a nail to drive out the pin for the smaller drive gear kit. Removed and replaced with new, used new pin to lock it on to the shaft. Changed out the bearings and washers on one powerscrew, put chain back on. Then was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Greased chain, gear drive and powerscrew. Put all covers back on with the screws. Pushed button it worked. Read more...
Your Price
$12.62
In Stock
Trash Compactor POWER NUT ASM
PartSelect Number PS16554596
Manufacturer Part Number WC02X20287
This power nut assembly is made to be used in conjunction with your trash compactor. It comes with five pieces that include the two mounting pins, two clips, and the new power nut. This piece is beige, and roughly 3 inches wide, and almost 2 inches long. For this repair, you will need a screwdriver set or a multi-screwdriver, a quarter-inch nut driver bit, and a flat-head bit. You will need to get inside of your trash compactor in order to replace this part. This means uninstalling your appliance from your cabinets.
Fixes these symptoms
- Compactor ram gets stuck
- See more...
Installation Instructions
john from joplin, MO
plastic nut was stripped
replaced drive nuts only problems i had was to adjust shutoff switch
Read more...
Your Price
$67.86
In Stock
Trash Compactor 15 Inch White Plastic Compactor Bags - 60 Pack
PartSelect Number PS1964577
Manufacturer Part Number W10165294RB
This is a 60-pack of plastic compactor bags. These bags are 15 inches wide, 3 millimeters thick and are white in color. The 3-millimeter thickness makes the bags more durable and helps prevent tearing. They are an environmentally-conscious product that are made of 50% post-consumer recycled material. The bags feature a Slip-N-Grip design that prevents the bag from slipping down into the compactor. Strong resin that is incorporated into the material increases puncture and tear resistance to help keep your trash in the bag. These bags will fit 15-inch rectangular compactors.
Your Price
$38.94
In Stock
Trash Compactor Frame Roller Assembly
PartSelect Number PS12716561
Manufacturer Part Number WC17X20084
Fixes these symptoms
- Drawer is hard to open and or close
- See more...
Your Price
$64.08
In Stock
Trash Compactor Directional Switch
I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where. Read more...
PartSelect Number PS11744742
Manufacturer Part Number WP777811
The function of the directional switch on your trash compactor is to ensure the ram lowers to compress your trash, then returns to the top position. If your trash compactor does not complete this task, will not stop at the end of the compacting cycle, or is noisy during operation, you may need to replace the directional switch. Be sure to disconnect your trash compactor from the power source before completing this repair. This is a fairly easy repair. After you open the control panel of the compactor, all you will need to do is unplug the old switch from the electrical wires, and plug the new switch in.
Fixes these symptoms
- Compactor ram gets stuck
- Doesn’t stop at end of compacting cycle
- Noisy
- See more...
Installation Instructions
Scott from Indianapolis, IN
Trash Compactor ram wouldn't lower
I pulled the trash compactor out from under the counter.I took out the four screws that kept the top cover in place to expose the ram.
The gear shafts were turning but the ram would not lower, at first I though the ram drive bolts were stripped and it wouldn't engage the shaft. Then I realized there was a mechanical directional\limit switch at the top that controlled the power and direction the gear shafts were turning, this switch was broken.
Just had to take off the front plate that was held on by a number of screws and replace the switch that was held on by two more screws. It had five wires attached to it, the new switch was clearly labeled as to which color wire went where. Read more...
Your Price
$26.42
In Stock
Trash Compactor 15 Inch Compactor Bags - 15 Pack
I quest I will have to try these all plastic bags. I hope they are strong enough and work properly. Read more...
PartSelect Number PS1964579
Manufacturer Part Number W10165295RP
Trash compactor bags are a practical way to discard your waste. Due to the extreme pressure of the compactor, trash compactor bags designed to handle the force are necessary. These bags are made from tough 2.5-millimeter, multi-laminate plastic, and the patented Slip-Grip design prevents the bag from slipping into the compactor bin. They measure approximately 15 inches wide x 15 inches high and are made from 50 percent post-consumer recycled plastic. This pack of 15 trash compactor bags is a genuine OEM replacement part, and will fit most rectangular 15-inch trash compactors.
Installation Instructions
Sherry from SALEM, NY
Paper & Plastic 15” Compactor Bags not available
I have always used compactor bags made of paper & plastic. I was sent bags made of only plastic. I called and was told that is the only kind available. I am concerned that the plastic bags may not be strong enough.I quest I will have to try these all plastic bags. I hope they are strong enough and work properly. Read more...
Your Price
$20.14
In Stock
Trash Compactor Drawer roller asm
PartSelect Number PS16591421
Manufacturer Part Number WC01X20232
The drawer roller attaches to the bottom of the drawer and allows the drawer to roll in and out.
Fixes these symptoms
- Drawer is hard to open and or close
- See more...
Your Price
$10.76
In Stock
Trash Compactor RETURN SWITCH
PartSelect Number PS16542383
Manufacturer Part Number WC21X20249
This is a top limit directional switch for a trash compactor. The directional switch reverses the motor direction when the trash compactor has reached the top of the drawer. If your trash compactor is not completing the compact cycle properly, you may have to test the switch. If you have a multimeter, you can perform a continuity test before ordering this part to determine if a continuous electrical path is present in the switch. If there is no electrical path in your switch, you will need to replace it. This is an authentic replacement part sourced directly from the original manufacturer.
Fixes these symptoms
- Doesn’t stop at end of compacting cycle
- Won’t stay on
- See more...
Installation Instructions
Brian from HOUSTON, TX
Trash compactor would not shut off at end of cycle. Would have to manually turn it off.
Removed compactor from opening. Using screw driver unthreaded 4 screws from top and then removed the on/off dial. Face plate came off easy and provided access to relay switch bank. Unscrewed two screws which allowed both relay switches to be removed and replaced. Recommend replacing both relay switches. Reassembled and compactor worked fine. Very easy job. If your compactor is making a machine gun noise during the return cycle then this will solve your problem.
Read more...
Your Price
$7.44
In Stock
Trash Compactor Foot, Front - Single
PartSelect Number PS11747965
Manufacturer Part Number WPW10001130
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.
Installation Instructions
Paddy from Ferndale, WA
Bearings went out in the drum.
purchased the bearings at Napa auto parts for 16$. Over all it was a little difficult to get the bearings out and back in. Used a brass drift to drive them out and to seat them back in..
Read more...
Your Price
$45.30
In Stock
Trash Compactor Switch Knob
Will definitely come back here, if I ever have a problem again. THANKS!!! Read more...
PartSelect Number PS11747576
Manufacturer Part Number WP9871800
This start switch knob, also known as a rotary switch knob, is used for a trash compactor. The knob allows you to activate the compactor when the knob is turned or pushed. It comes in black and it measures about one and a half inches in diameter. Remove the knob by pulling it out of the switch. No tools are required for this easy replacement, but refer to the diagram and installation instructions provided by the manufacturer for accurate guidance and more detail.
Fixes these symptoms
- Won’t start
- Won’t stay on
- See more...
Installation Instructions
Steffanie from Mill Valley, CA
Lost knob to trash compactor
Ordered the part here, had it delivered to my front door, and fixed it in LESS than 24 hrs.Will definitely come back here, if I ever have a problem again. THANKS!!! Read more...
Trash Compactor Brands
- Amana Trash Compactor Parts
- Electrolux Trash Compactor Parts
- Frigidaire Trash Compactor Parts
- GE Trash Compactor Parts
- Hotpoint Trash Compactor Parts
- Jenn-Air Trash Compactor Parts
- Kenmore Trash Compactor Parts
- KitchenAid Trash Compactor Parts
- Magic Chef Trash Compactor Parts
- Maytag Trash Compactor Parts
- Roper Trash Compactor Parts
- Speed Queen Trash Compactor Parts
- Whirlpool Trash Compactor Parts
Related Trash Compactor Parts
- Trash Compactor Hardware
- Trash Compactor Transmissions and Clutches
- Trash Compactor Switches
- Trash Compactor Knobs
- Trash Compactor Handles
- Trash Compactor Panels
Popular Trash Compactor Models
Below are the most popular Trash Compactor models we have. Enter your model number in the search box to find your model.
