Ryobi Parts
Popular Ryobi Parts
Your Price
$11.12
In Stock
Ryobi Sanding Pad Assembly Hook and Loop - 5 Inch
PartSelect Number PS10095105
Manufacturer Part Number 300527002
It is a genuine OEM sourced 5-inch sanding pad assembly that is specially designed for use with Craftsman orbital sanders. Its purpose is to provide support for hook and loop sandpaper, unfortunately, over time it may wear out or get damaged eventually requiring a replacement. To make the pad last longer do not put to much pressure on the sander when using it, the pressure will create heat and ruin the small hooks on the pad. To replace the pad simply remove the four screws attaching it to the sander and replace it with the new pad. Please note this high-quality component is sold individually.
Your Price
$13.31
On Order
Your Price
$5.49
In Stock
Ryobi Brush (2 Required 7 X 17 X 19/17)
PartSelect Number PS10076327
Manufacturer Part Number 0502025007
Your Price
$6.63
In Stock
Your Price
$12.79
In Stock
Your Price
$8.04
In Stock
Your Price
$4.99
In Stock
Your Price
$6.21
In Stock
Ryobi Bearing
HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
PartSelect Number PS9006914
Manufacturer Part Number 532009040
The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft. Over time, the part may become worn and damaged, which you will notice if you experience a squealing or grinding sound from the wheel in question, or you notice the wheel is sloppy on the shaft.
You will need a hammer and punch to complete this repair, which most of our customers rated as easy. Make sure you tap the new bearing into place evenly inside the tire rim.
Installation Instructions
robert from EUREKA, CA
transaxle rotated forward on 2015 Husqvarna YT42DXLS
2015 Husqvarna YT42DXLS. Both transaxle support struts broke causing the transaxle rotated forward and shear transaxle mounting bracket. The transaxle was not damaged. All 3 parts required replacement. There are some good youtube videos to watch to show how to complete the repair. HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
Your Price
$4.99
In Stock
Your Price
$5.79
In Stock
Related Ryobi Parts
- Ryobi Blower Parts
- Ryobi Chainsaw Parts
- Ryobi Clearing Saw Parts
- Ryobi Cultivator Parts
- Ryobi Edger Parts
- Ryobi Hedge Trimmer Parts
- Ryobi Lawn Mower Parts
- Ryobi Lawn Tractor Parts
- Ryobi Pole Saw Parts
- Ryobi Snow Blower Parts
- Ryobi String Trimmer Parts
- Ryobi Tiller Parts
- Ryobi Vacuum Parts
Popular Ryobi Models
Below are the most popular Ryobi models we have. Enter your model number in the search box to find your model.
- SG1000 Angle Grinder
- RYi2200 Digital Inverter Generator
- P4360 18 Volt Pole Saw
- P4360 P4360 18 Volt Pole Saw Mfg. No. 107369007 1-24-22 (Rev:02)
- P4360 P4360 18 Volt Pole Saw Mfg. No. 107369001 12-15-20 (Rev:06)
- RY80940B Pressure Washer
- 110 Trimmer
- 410r Tiller
- 410r Tiller
- 410r Tiller
- 410r Tiller
- 410r Tiller
- 410r Tiller
- 410r Tiller
- RY80940 Pressure Washer
- RY14122 Pressure Washer
- RY14122 Ry14122 Pressure Washer Mfg. No. 090079270 5-21-19 (Rev:06)
- RY14122 Ry14122 Pressure Washer Mfg. No. 090079210 2-27-18 (Rev:03)
- UT33600 26cc String Trimmer Ut-33600 26cc String Trimmer
- RY43160 Electric Pole Saw
