Troy-Bilt Snow Blower Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Troy-Bilt Snow Blower Parts
Your Price
$3.99
In Stock
Troy-Bilt Snow Blower Shear Pin
PartSelect Number PS9110822
Manufacturer Part Number 738-04124A
This individually sold shear pin is an OEM replacement that is most typically used in snowblowers but can also be used within snowblower attachments for lawn tractors. Its main uses are connecting the auger and auger shaft, which are the rotating blades, and to protect more valuable components such as the transmission.If the snow is causing excessive force or there is a jam within the auger and connected housing,it will cause the shear pin to snap, effectively stopping the rotation of the auger, while the auger shaft and gears will continue turning. If the shear pin snaps, snow will simply build up on the outside of the auger housing, since the auger will no longer spin. This shear pin has a .25-inch diameter, and 1.5-inch length and is sold individually. Most augers have a pin on each side, so you may need to purchase more than one, and it is also recommended that you carry spare pins in case of a future breakage.
Your Price
$12.52
In Stock
Troy-Bilt Snow Blower Clip-hold Down (nylon)
PartSelect Number PS9903766
Manufacturer Part Number 1724869099
Hold-down clips, also known as retaining, locking or fastening clips, are designed to secure and fasten specific parts within equipment, and the use depends on the type and model. This hold down clip is used to secure the chute of various models of snowblowers, and is sold as an individual OEM part, without any securing hardware. Made of nylon, this clip secures to the chute with two screws and two washers. If you notice a wobbly or insecure chute resulting in excessive vibrations from the chute, check to make sure the clip is in-place before inspecting it for damage and ordering a replacement. To replace this clip, you will need to gain access to the chute, with either a screwdriver or wrench, and once you can access it, it is as simple as unscrewing the old clip and installing the new clip and rest of the assembly.
Your Price
$5.07
In Stock
Your Price
$35.17
Special Order
Troy-Bilt Snow Blower Shave Plate (24 In)
PartSelect Number PS9306313
Manufacturer Part Number 790-00120-0638
Your Price
$5.95
Special Order
Troy-Bilt Snow Blower Chute Flange Keeper
PartSelect Number PS10005747
Manufacturer Part Number 731-0851A
This chute flange keeper is sourced from the original equipment manufacturer for use in snowblowers. The plastic keeper allows the snowblower chute to pivot, and secures the flange that connects the chute to the blower frame and holds it in place during use. Over time the flange keeper can break or fall off, which causes the chute to dislodge or shift from its position. If you notice that debris is discharged in the wrong direction, and you have difficulties adjusting the chute then this is a sign that the flange keeper is no longer functioning as it should. Clean the chute flange and surrounding area before placing the new keeper on. Use a pair of pliers to align the the holes on the flange keeper with the holes on the chute and lock it in place.
Your Price
$5.95
In Stock
Troy-Bilt Snow Blower Lawn Mower Flanged Lock Nut
PartSelect Number PS9095080
Manufacturer Part Number 712-04065
Designed for use in various models of lawn and garden equipment, this part is not sold as part of a kit or assembly. It is made of metal, is gold in color, and is sold individually. This part may also be called a Flange Lock. This nut is designed to lock in place, preventing vibrations and other parts coming loose.
This nut may be located in multiple locations on your machine, refer to your owners manual to determine if this is the correct part. You will need a wrench or socket set and a torque wrench to complete this repair. You should only torque the nut to the manufacturer recommendation, no tighter.
You will need to replace this part when it is worn or damaged. While this part can wear through regular use, it is most commonly damaged through improper use of a wrench or socket.
Customers describe this repair as Easy.
Your Price
$5.95
In Stock
Troy-Bilt Snow Blower Tiller Cable Barrel Holder
PartSelect Number PS9167431
Manufacturer Part Number 946-0605
This cable barrel holder is a genuine OEM part that is designed for use with tillers and snow throwers. Sold as an individual part, this holder measures approximately 1-inch in length and is used to secure the clutch control handle and cable together. This holder is made of durable plastic and can replace the old holder by simply removing it, inserting the cable into the new holder, and tightening it until it is locked in place.?
Installation Instructions
Carl from DECATUR, TX
Seized bearing and spacer on bolt shaft for idler pulley
Unfortunately I couldn’t find the spacer on the Internet, so I ended up going to the hardware store and buying multiple sizes of spacers and bearings to complete the install. I ended up using a steel spacer with shoulder and two bearings. Way overkill, but worth the three dollars.
Read more...
Your Price
$5.95
In Stock
Troy-Bilt Snow Blower Chute Flange Keeper
PartSelect Number PS9104771
Manufacturer Part Number 731-04869A
The chute flange keeper is a genuine OEM replacement part that secures the chute flange on snowblowers. The keeper is made of plastic and fits onto the metal piece, known as the flange, that connects the chute to the blower frame and holds it in place during use. Over time the flange keeper may wear down or fall off and cause the chute flange to fall out of alignment. If you notice that you have difficulties adjusting the direction of the chute and you hear rattling during use, then this is a sign that the flange keeper is no longer properly attached. Before positioning the new keeper, clear off any dirt or debris in the area. Use a pair of pliers to fit the keeper on and align the holes on the flange keeper with the holes on the chute before securing it.
Your Price
$5.95
In Stock
Troy-Bilt Snow Blower Locking Flange Nut
PartSelect Number PS9092936
Manufacturer Part Number 712-04063
This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant to loosening when threaded on a bolt. It has a variety of applications and is used in multiple locations on most models. Please refer to your owners manual to determine the exact location.
While made of durable metal, the ends can round off from improper use of a wrench or socket. Depending on the location, this part may also become worn through regular use of your machine. It should be replaced when visibly cracked, worn or damaged. To complete this repair, you will need a wrench or socket, and a torque wrench. Ensure you torque the bolt according to the manufacturer recommendations.
Customers rate this repair as Easy.
Your Price
$3.99
In Stock
Troy-Bilt Snow Blower Carburetor Gasket Plate
PartSelect Number PS17016727
Manufacturer Part Number 751P11897B
This genuine carburetor gasket plate is an original replacement part sourced directly from the manufacturer for use in snowblowers by MTD, Yard Machines, Troy-Bilt, Yard Man, and Cub Cadet. Positioned between the carburetor and the choke control bracket, this component is essential for creating a secure, airtight seal that ensures proper engine performance. Made from a thin, durable material, the gasket plate may require replacement if it becomes damaged or worn. This item is sold individually and may require a socket set and pliers for installation. For best results, consult your equipment’s service manual and perform the repair with the engine off and cool.
Installation Instructions
Jason from PEABODY, MA
Carburetor rebuild
I can’t complete this easy repair because partselect sent the wrong part and has not responded to customer service requests. Please contact me- jtandree@gmail.com
Read more...
Troy-Bilt Snow Blower Appliance Types
Related Troy-Bilt Snow Blower Parts
- Troy-Bilt Snow Blower Bearings
- Troy-Bilt Snow Blower Gears
- Troy-Bilt Snow Blower Handles
- Troy-Bilt Snow Blower Seals and Gaskets
- Troy-Bilt Snow Blower Skid Shoes
- Troy-Bilt Snow Blower Spark Plugs
- Troy-Bilt Snow Blower Springs and Shock Absorbers
- Troy-Bilt Snow Blower Wheels and Rollers
Popular Troy-Bilt Snow Blower Models
Below are the most popular Troy-Bilt Snow Blower models we have. Enter your model number in the search box to find your model.
- 31BM63P3711 Storm 2620
- 31BM63P3711 Storm 2620
- 31BM63P3711 Storm 2620
- 31BM63P3711 Storm 2620 Snowblower
- 31BM63P3711 Storm 2620
- 31AS62N2711 Storm 2410
- 31AS62N2711 Storm 2410 Snowblower
- 31AS62N2711 Storm 2410
- 31AS62N2711 Storm 2410
- 31AS62N2711 Storm 2410
- 31AH64Q4711 Storm 2840
- 31AH64Q4711 Storm 2840
- 31AH64Q4711 Storm 2840 Snowblower
- 31AH64Q4711 Storm 2840
- 31AH55Q5711 Snowblower
- 31AS2T5F711 Squall 2100
- 31AS2T5F711 Squall 2100
- 31AS2T5F711 Squall 2100
- 31AS2T5F711 Squall 2100 Snowblower
- 31AS2T5F711 Squall 2100