Troy-Bilt Tiller Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Troy-Bilt Tiller Parts
Your Price
$26.83
In Stock
Troy-Bilt Tiller Fuel Tank Assembly W/fuel Lines Incl. 29
PartSelect Number PS11812933
Manufacturer Part Number 753-06797
The fuel tank assembly is responsible for storing and supplying fuel to the engine in lawn and outdoor power equipment. It includes the tank, fuel cap, and fuel lines. The fuel tank assembly will fail if the tank develops cracks or leaks, or if the fuel lines can become clogged. When the fuel tank assembly fails, you will notice fuel leakage, restricted fuel supply, stalling, difficulties starting and overall lower performance. Before beginning any repairs, first drain any remaining fuel from the tank for your safety. Disconnect the fuel lines from the tank and remove the fuel tank from the equipment. Position the new tank on to the mounting holes and secure it in place. Connect the fuel lines to the engine and vent to complete your repair.
Fixes these symptoms
- Will Not Start
- See more...
Installation Instructions
Robert from ORANGE, CA
One of the two fuel lines cracked and leaking
Removed the 6 screws holding the red plastic cover, tank, and the old fuel lines from the carburetor. Placed the new tank in the sunlight for a few minutes to soften the new fuel lines. Then attached the new lines to the carburetor and replaced the cover
Read more...
Your Price
$14.13
Special Order
Your Price
$5.95
In Stock
Troy-Bilt Tiller Cultivator Air Filter
PartSelect Number PS9117898
Manufacturer Part Number 753-05996
Your Price
$5.95
In Stock
Troy-Bilt Tiller Cable Barrel Holder
PartSelect Number PS9167431
Manufacturer Part Number 946-0605
This cable barrel holder is a genuine OEM part that is designed for use with tillers and snow throwers. Sold as an individual part, this holder measures approximately 1-inch in length and is used to secure the clutch control handle and cable together. This holder is made of durable plastic and can replace the old holder by simply removing it, inserting the cable into the new holder, and tightening it until it is locked in place.?
Your Price
$5.95
In Stock
Troy-Bilt Tiller Snow Blower Locking Flange Nut
PartSelect Number PS9092936
Manufacturer Part Number 712-04063
This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant to loosening when threaded on a bolt. It has a variety of applications and is used in multiple locations on most models. Please refer to your owners manual to determine the exact location.
While made of durable metal, the ends can round off from improper use of a wrench or socket. Depending on the location, this part may also become worn through regular use of your machine. It should be replaced when visibly cracked, worn or damaged. To complete this repair, you will need a wrench or socket, and a torque wrench. Ensure you torque the bolt according to the manufacturer recommendations.
Customers rate this repair as Easy.
Your Price
$25.45
In Stock
Troy-Bilt Tiller Edger Bearing
PartSelect Number PS9167498
Manufacturer Part Number 941-0155
This authentic OEM bearing measures 0.62 inches inside diameter, and 1.38 inches outside diameter, and is 0.436 inches thick. Silver and balck in color and sold individually, the bearing is comprised of steel and rubber.
This bearing allows the input shaft to rotate freely inside the gear box, and over time can become worn or damaged. You will know your bearing is damaged if it is making a growling, grinding, or squealing sound. This is an easy repair, and requires a bearing puller tool to carry out.
Locate the bearing inside the gear box on each end of the input shaft, ensuring you have confirmed this is the part you need by verifying your model number or using your owners manual.
Your Price
$26.85
In Stock
Troy-Bilt Tiller Lawn Mower Drive Belt
PartSelect Number PS9172714
Manufacturer Part Number 954-04032B
This genuine drive belt is an original replacement part sourced directly from the manufacturer and is commonly used in Craftsman lawn mowers and edgers. Made from flexible rubber, it transfers power from the engine to the pulley that drives the cutting blades. Over time, the belt may become brittle or cracked due to wear and exposure, requiring replacement to maintain optimal performance. Measuring 3L x 35.80 inches, this belt is sold individually. A wrench may be needed for installation, depending on your equipment model.
Your Price
$35.24
Special Order
Troy-Bilt Tiller Lawn Mower Throttle Box Assembly
PartSelect Number PS10017243
Manufacturer Part Number 831-0823A
The Throttle Box Assembly, or the Throttle Assembly, is a kit that includes the housing, handle, and hardware. It is black and constructed of steel and plastic. It can be installed onto the right hand upper handle, using a screwdriver and pliers, and is rated as Medium difficulty to install.
This kit contains the parts that control the amount of the air and fuel entering the engine. When the part breaks (likely due to fatigue) you will no longer be able to control the engine. If nothing happens when you move the handle, that means it has become disconnected. When the part is broken it must be replaced. Check your model number to ensure you are selecting the correct replacement part.
Your Price
$5.95
In Stock
Troy-Bilt Tiller Snow Blower Fuel Drain Plug
PartSelect Number PS9087643
Manufacturer Part Number 710-04938
Your Price
$21.43
In Stock
Troy-Bilt Tiller Forward Drive Belt
PartSelect Number PS10035467
Manufacturer Part Number 954-04090
The Forward Drive Belt is a 12.5-inch black, rubber belt, sold individually. Installation of this manufacturer-certified part is rated as "Easy" by customers and will require pliers, a socket set, and a wrench set. This part is used to transfer power from the engine's drive pulley to the transmission. If broken due to wear/fatigue/damage, the drive wheels will no longer be able to propel the mower, and the part should be replaced. This belt attaches between the engine drive pulley and the transmission's drive pulley. Refer to your make, model and diagrams to ensure this part is right for you.
Troy-Bilt Tiller Appliance Types
Related Troy-Bilt Tiller Parts
- Troy-Bilt Tiller Bearings
- Troy-Bilt Tiller Belts
- Troy-Bilt Tiller Brackets and Flanges
- Troy-Bilt Tiller Caps and Lids
- Troy-Bilt Tiller Carburetors
- Troy-Bilt Tiller Control Cables
- Troy-Bilt Tiller Filters
- Troy-Bilt Tiller Handles
- Troy-Bilt Tiller Hoses and Tubes
- Troy-Bilt Tiller Knobs
- Troy-Bilt Tiller Oil Plugs
- Troy-Bilt Tiller Seals and Gaskets
- Troy-Bilt Tiller Spark Plugs
- Troy-Bilt Tiller Springs and Shock Absorbers
- Troy-Bilt Tiller Switches
- Troy-Bilt Tiller Transmissions and Clutches
- Troy-Bilt Tiller Wheels and Rollers
Popular Troy-Bilt Tiller Models
Below are the most popular Troy-Bilt Tiller models we have. Enter your model number in the search box to find your model.
- TB146EC Tiller
- TB146EC Tiller
- TB146EC Tiller
- TB146EC Tiller
- TB146EC Super Bronco Tiller
- TB146EC Tiller
- 12103 1.5hp Roto-Tiller
- 12209 Tiller
- 12210 Bronco RotoTiller
- TB225 Tb225 21bk225g766
- TB225 Tiller
- TB225 Tb225 21ak225g766 21ak225g766
- 21BA144R966 Cultivator
- 5150 Pony V 5hp Elec
- 20458 Pony I 5hp Elec
- 21CA144R966 Cultivator
- 12089 (0100101) Rear-Tine Horse Tiller
- 15008 (0300101-0399999) Pony Tiller
- 15008 15008 Pony Vii Opc (5hp)(S/N S0242650-S0254903)
- 15008 Tiller