Whirlpool Washer Seals and Gaskets
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Whirlpool Washer Seals and Gaskets
Your Price
$40.95
In Stock
Whirlpool Washer Dryer Drum Felt Seal
PartSelect Number PS8691753
Manufacturer Part Number W10612022
This is a genuine OEM replacement rear drum seal for your dryer. This seal is made of felt and comes with the adhesive required for installation. The purpose of the seal is to prevent hot air from escaping the drum while the dryer is operating. If you notice that it is taking too long for your laundry to dry, that marks are left on your laundry, or the machine is noisy or will not tumble, then you may need to replace the seal.
Fixes these symptoms
- Drum Not Spinning
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Paul from Monmouth, IL
intermittant heat
First I shut off the gas supply and disconnected the dryer vent and unpluged the unit so you can access the rear of the dryer. Then I removed the rear cover. This is where you will find your thermostats and fuses. Holding the new part next to the one to be replaced I transfer the wires one at a time so as not to get them mixed up, then unscrew the old part and install the new one. Insert a flat blade screwdriver under the top cover in the 2 front corners to unsnap it from it's clips, also at this time you need to remove the 2 screws that hold the upper part of the lint filter tube to the lid, then lift the lid to expose the drum ( I tilted the dryer back as far as the flex gas line would allow me to and rested the top lid against the wall without removing it, to many wires). Behind the front cover in the top right corner is the plug for the door switch,un-plug it and also there are 2 screws one in each corner. After that lift the front cover straight up and pull it away from the cabinet ( it has clips at the bottom to hold it in place). Reaching under the drum on the right side pull down on the belt tensioner and release the belt from the motor then you can remove the drum. Laying the drum down on it's front edge I removed the rear felt seal and took a piece of sand paper to rough up th old glue and clean off some of the felt that was still stuck to the drum. Following the directions from the seal package I put the glue around the edge of the drum and re-installed the new felt. This is a good time to clean out your dryer, while the glue sets up. A shop vac works the best, but be carefull not to suck up the money, it will help pay for the repair ( I found over a dollar in change ). At this time I also changed the coils on the gas valve, remove the 2 screws that hold the clamp and replace them one at a time. Re-install the drum with the belt on it, fold it and push it through the tensioner and put it on the motor pulley. rotate the drum to make sure that the felt is not kinked under itself, re-install the front cover bottom clips first, then the 2 screws and the plug for the door switch, pull down the lid and snap it in place, before installing the rear cover this is a good time to remove the rear cover to the lint chute and clean in there also ( it's easy to see why there are so many dryer fires). Re- install that cover and the rear cover and vent tube, turn your gas back on and check it for leaks ( even if you didn't disconnect it) plug your dryer back in and get busy catching up on the laundry that you haven't had a chance to do because your dryer broke, then smile and think about all the money you saved by doing this simple repair your self. Thanks Parts Select
Read more...
Your Price
$118.09
On Order
Whirlpool Washer Front Load Bellow
PartSelect Number PS12074757
Manufacturer Part Number W11106747
This is a door bellow, also known as a door seal gasket, made for various models of washing machine. This bellow is designed to seal the inner drum of the washer from the outside of the washing machine and its internal components. If your washer is currently experiencing issues with leaking, this gasket is likely worn out and in need of replacing. This gasket is made of gray rubber and is sold as an individual OEM part and is sold separately from its necessary clamp.
Fixes these symptoms
- Draining Issues
- Leaking
- Marks left on clothes
- See more...
Your Price
$135.42
In Stock
Whirlpool Washer Bellow
PartSelect Number PS12711495
Manufacturer Part Number W11314648
This genuine OEM door bellow, also known as a door boot seal, is sourced directly from the manufacturer for use in front load washing machines. It is a flexible rubber seal that is found around the opening of the washer door. It is responsible for creating a watertight seal between the door and tub during the wash cycle. It also absorbs vibrations and reduces noise while the washer is running. If the seal is torn, worn down or no longer able to remain securely attached to the washer frame it will need to be replaced promptly. A faulty seal will result in water and detergent leakage and potential injury as well as increased noise from the washer.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Kaitlyn from TRENTON, KY
There were holes in our seal. Water was leaking during every wash.
We unplugged everything. Then we removed the screws from the back of the washer. Then we slid off the top of the washer. Next, we removed the bottom drawer of the washer. We then proceeded to remove all of the screws and took off the entire face of the washer until the bellow was completely exposed. We did have to detach the hose and door clamp. We removed two metal clamps that held the seal in place. Once those were off we removed the entire old seal, replaced it with the new one, clamped it down, and reversed the steps to put everything back together. It was fairly simple.
Read more...
Your Price
$10.45
In Stock
Whirlpool Washer Dryer Lint Trap Housing Seal
PartSelect Number PS11741506
Manufacturer Part Number WP339956
This is foam seal for your dryer. It forms a seal to prevent air from escaping the rear of the dryer drum and the lint duct. This model comes with adhesive backing and is located in between the lint chute and the bulkhead of your appliance. This foam seal is just over 28 inches long and under 1 inch wide. You may need to replace this part if your clothing is taking too long to dry, or if your dryer is not generating enough heat or no heat at all.
Fixes these symptoms
- Noisy
- Not Heating
- Too hot
- See more...
Installation Instructions
Eric from Fort Dodge, IA
dryer drum not turning and no air circulating
replaced motor and drum rear seal as well as idler wheels, the old rear drum seal was completly worn out, since I had it all apart, I replaced lint chute and trap seals and belt and tensioner. I spent less money on parts than if I would have bought a new dryer. The motor was the main problem as the bearings were shot.
Read more...
Your Price
$103.95
On Order
Whirlpool Washer Bellow Door Boot Seal - Gray
The only difficult part was putting the outside band clamp on over the bellow without it slipping out of place - took a few tries. The video was very helpful - I did put hardware into plastic bags based on the steps in the removal for so that I wouldn't forget (or get them mixed up).
I was able to do this project while home from work with a sick kindergartener. Problem started and did the removal the first day ordered the part and it arrived 2 days later - install complete in less than an hour. We went back to school/work with a operating washer by the end of the week! Thank you - it was actually kinda fun and my son bragged to his grandfather that 'he and momma fixed the washer'. Read more...
PartSelect Number PS11753988
Manufacturer Part Number WPW10381562
This door boot, also known as a door seal, is compatible with various models of front load washing machines. It is a genuine OEM replacement part that is sourced directly from the manufacturer to ensure the best fit with your appliance. The door boot is made of rubber, and it is responsible for creating a tight seal between the tub and the door to prevent water and detergent from leaking out of the washer when it is in use. This helps to prevent injuries and ensure the efficient running of the appliance. It is common for the door boot to wear down over time. It will need to be replaced if it can no longer securely fit around the door frame or if it is torn or cracked.
Fixes these symptoms
- Leaking
- Marks left on clothes
- See more...
Installation Instructions
Laura from WAYLAND, MA
Washer leaking - noticed large crack in the seam of the bellow
9 year old washer started leaking - after inspecting noticed a large hole in the bellow. The only difficult part was putting the outside band clamp on over the bellow without it slipping out of place - took a few tries. The video was very helpful - I did put hardware into plastic bags based on the steps in the removal for so that I wouldn't forget (or get them mixed up).
I was able to do this project while home from work with a sick kindergartener. Problem started and did the removal the first day ordered the part and it arrived 2 days later - install complete in less than an hour. We went back to school/work with a operating washer by the end of the week! Thank you - it was actually kinda fun and my son bragged to his grandfather that 'he and momma fixed the washer'. Read more...
Your Price
$119.95
On Order
Whirlpool Washer Bellow
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached about 3" connected to a small diameter wire (1mm.) that runs all the way around the outside portion of the bellow.
Use a small screwdriver or other to pull and pry the spring away from the rubber bellow. Be careful not to damage the spring or ring. Once you have grip on it, pull it carefully toward you then up and off of the bellow.
The front portion of the bellow is now free and can be peeled off. Start at any point and pull the rubber bellow in toward the opening of the washer, it comes off easily.
When you get to the detergent outlet on the upper left side, grab the plastic tube and carefully pull the bellow from around it. There is no adhesive or clamp holding this in place, just friction. Remove the rest of the front portion of the bellow.
Push as much of the bellow into the washer as possible to get it out of the way.
Once this is off comes the slightly tricky part. Look up at the top right portion of the bellow that is still attached. You may need to feel with your hand but you should be able to see it. You are looking for the screw/nut end of a giant hose clamp. This hose clamp goes around the entire bellow and the secures it to the portion that holds the basket.
This is where the stubby screw driver comes in handy. There is not nearly enough room for a standard one and a nut driver or wratchet are too big. The nut will be pointing down and will need to be replaced the same way.
Loosen the hose clamp almost all of the way, not necessary to have the hose clamp come completely apart.
You can now remove the entire hose clamp from around the bellow by pulling it forward.
You will need to remove the hose clamp from the washer. To do this, squeeze it in from the sides about 6", don't kink it. Push it down toward the floor between the basket and the metal front panel. You will now be able to remove it from the top of the opening and be able to pull the bottom portion out.
Pull the old bellow completely out, very easy to do.
Time to install the new bellow. Figure out which side goes in and which faces out. The big hint is that the water inlet is on the upper left side.
You will notice at the top of the bellow on the portion that goes inside of the washer, you will find a small triangular shaped tab about 1/4" high. This is your centering mark. This will be at the very top. If you keep this at the top, everything will line up perfectly.
Slip the bellow over the edge of the portion that holds the basket where you removed the old one. I started at the top and worked left so I could install the detergent inlet tube. Pull this through the bellow carefully. It doesn't take a lot of force.
As you are pressing the bellow on this lip, you will notice that there is a 1/2" high back stop all of the way around. This is great because as you press it on, there is a positive stop and you can't go further than necessary. Continue to press it in all of the way around.
Now it is time to install the Hose clamp. Un bend anything that might have bent on the clamp. With the nut at the top or top right with the nut facing down to the floor while holding it vertically, squish it slightly inward, put the bottom portion in first then the top portion. Orient is as it was when you took it off. Slide it around the bellow. You will feel a positive stop.
Grab the stubby screwdriver and tighten down the hose clamp. I did about a medium force when tightening. It doesn't take a lot of force.
Now it is time to pull the remaining part of the bellow out of the basket and fit it into place. Press it around the outside portion of the opening so it hooks over the lip. This w Read more...
PartSelect Number PS11744957
Manufacturer Part Number WP8182119
This is a door bellow, also known as a door gasket or seal, that is compatible with washing machines. Door bellows are used as a method to seal the inner drum of the washing machine and the soapy water inside it, from the rest of the washer cabinet and your home. If you notice any leaks at the front of your washing machine, this door bellow may be worn out or damaged, so inspect it to ensure it needs replacing. This door bellow is made of a thick rubberized material and wraps around the inner drum and will need a clamp to stay secure. This door bellow is sold as an individual OEM part and is not sold with any other parts or accessories.
Fixes these symptoms
- Leaking
- Marks left on clothes
- See more...
Installation Instructions
Franck from Annandale, VA
Bellows were moldy, needed to replace
The first step is to remove the retainer ring that holds the outside of the bellow in place.To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached about 3" connected to a small diameter wire (1mm.) that runs all the way around the outside portion of the bellow.
Use a small screwdriver or other to pull and pry the spring away from the rubber bellow. Be careful not to damage the spring or ring. Once you have grip on it, pull it carefully toward you then up and off of the bellow.
The front portion of the bellow is now free and can be peeled off. Start at any point and pull the rubber bellow in toward the opening of the washer, it comes off easily.
When you get to the detergent outlet on the upper left side, grab the plastic tube and carefully pull the bellow from around it. There is no adhesive or clamp holding this in place, just friction. Remove the rest of the front portion of the bellow.
Push as much of the bellow into the washer as possible to get it out of the way.
Once this is off comes the slightly tricky part. Look up at the top right portion of the bellow that is still attached. You may need to feel with your hand but you should be able to see it. You are looking for the screw/nut end of a giant hose clamp. This hose clamp goes around the entire bellow and the secures it to the portion that holds the basket.
This is where the stubby screw driver comes in handy. There is not nearly enough room for a standard one and a nut driver or wratchet are too big. The nut will be pointing down and will need to be replaced the same way.
Loosen the hose clamp almost all of the way, not necessary to have the hose clamp come completely apart.
You can now remove the entire hose clamp from around the bellow by pulling it forward.
You will need to remove the hose clamp from the washer. To do this, squeeze it in from the sides about 6", don't kink it. Push it down toward the floor between the basket and the metal front panel. You will now be able to remove it from the top of the opening and be able to pull the bottom portion out.
Pull the old bellow completely out, very easy to do.
Time to install the new bellow. Figure out which side goes in and which faces out. The big hint is that the water inlet is on the upper left side.
You will notice at the top of the bellow on the portion that goes inside of the washer, you will find a small triangular shaped tab about 1/4" high. This is your centering mark. This will be at the very top. If you keep this at the top, everything will line up perfectly.
Slip the bellow over the edge of the portion that holds the basket where you removed the old one. I started at the top and worked left so I could install the detergent inlet tube. Pull this through the bellow carefully. It doesn't take a lot of force.
As you are pressing the bellow on this lip, you will notice that there is a 1/2" high back stop all of the way around. This is great because as you press it on, there is a positive stop and you can't go further than necessary. Continue to press it in all of the way around.
Now it is time to install the Hose clamp. Un bend anything that might have bent on the clamp. With the nut at the top or top right with the nut facing down to the floor while holding it vertically, squish it slightly inward, put the bottom portion in first then the top portion. Orient is as it was when you took it off. Slide it around the bellow. You will feel a positive stop.
Grab the stubby screwdriver and tighten down the hose clamp. I did about a medium force when tightening. It doesn't take a lot of force.
Now it is time to pull the remaining part of the bellow out of the basket and fit it into place. Press it around the outside portion of the opening so it hooks over the lip. This w Read more...
Your Price
$16.79
In Stock
Whirlpool Washer Dryer Seal
But anyway the parts cam very quick and had easy to follow directions.
I would reccomend part select. Matt Read more...
PartSelect Number PS12745423
Manufacturer Part Number W11415783
This seal comes with the adhesive backing.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Matthew from East Islip, NY
drum stopped turning on dryer
Great! Spent about $36.00 and I ended up with a overhauled dryer. I ended up cleaning the whole thing out, it's amazing how much stuff accummulates in the frame of a dryer, I also found about $2.00 in change. It's a good idea to clean out a dryer every few years and the broken belt forced me to do it. But anyway the parts cam very quick and had easy to follow directions.
I would reccomend part select. Matt Read more...
Your Price
$7.95
In Stock
Whirlpool Washer Centerpost Gasket
PartSelect Number PS11723081
Manufacturer Part Number W10814296
This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edge, black in color, and made of plastic material. To perform this repair, you will need to disconnect the power, drain hose, and the inlet hose. You will need to remove the entire outside cabinet to have access to the tub assembly. The tub will need to be removed entirely. This is a genuine part that is sourced directly from the manufacturer.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Dexter from Milwaukie, OR
Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go.
Read more...
Your Price
$48.95
In Stock
Whirlpool Washer Door Gasket
PartSelect Number PS11731610
Manufacturer Part Number W10861521
This door seal does not include the adhesive glue.
Fixes these symptoms
- Door won’t close
- Marks left on clothes
- See more...
Installation Instructions
Manolak from MURFREESBORO, TN
Door Gasket tore out
Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine....
Read more...
Your Price
$103.95
On Order
Whirlpool Washer Front Load Bellow (gray)
PartSelect Number PS11748353
Manufacturer Part Number WPW10111435
Also known as a door boot seal.This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
Fixes these symptoms
- Leaking
- Marks left on clothes
- See more...
Installation Instructions
Marty from Belfair, WA
Water leak from bottom of door.
I discovered water leaking from the bottom of the door on our Kenmore front load washer. I did a little self diagnosis from the internet and found that this seems to be a common problem for front load Kenmore washers and that the ususal suspect is the large rubbery bellows. I examined the bellows on my washer and although I didn't find anything wrong with it, I couldn't find any other likely causes. I shopped around and found PartSelect to be the cheapest for the replacement part. Removal is easy by removing the lower front panel with three small screws on the bottom front, then remove the very top panel and then the top front control panel and finally the door panel. the bellows are actually held in place with a spring loop on the outer and a screw tightener on the inner, both are fairly easy to remove and the bellows comes right off. For installation my best advice is to lube the bellows with a small amount of dishwashing soap in the groove that fits on the washer tub. This will help it slide into place and enables a small amount of sliding fine tuning once it is on. From there it is just a reverse of the removal.
Read more...
Related Whirlpool Washer Parts
- All Whirlpool Washer parts
- Whirlpool Washer Agitators
- Whirlpool Washer Bearings
- Whirlpool Washer Belts
- Whirlpool Washer Brackets and Flanges
- Whirlpool Washer Caps and Lids
- Whirlpool Washer Circuit Boards and Touch Pads
- Whirlpool Washer Dispensers
- Whirlpool Washer Doors
- Whirlpool Washer Drawers and Glides
- Whirlpool Washer Drums and Tubs
- Whirlpool Washer Electronics
- Whirlpool Washer Elements and Burners
- Whirlpool Washer Filters
- Whirlpool Washer Handles
- Whirlpool Washer Handles and Latches
- Whirlpool Washer Hardware
- Whirlpool Washer Hinges
- Whirlpool Washer Hoses and Tubes
- Whirlpool Washer Knobs
- Whirlpool Washer Latches
- Whirlpool Washer Legs and Feet
- Whirlpool Washer Lights and Bulbs
- Whirlpool Washer Motors
- Whirlpool Washer Panels
- Whirlpool Washer Power Cords
- Whirlpool Washer Pulleys
- Whirlpool Washer Pumps
- Whirlpool Washer Sensors
- Whirlpool Washer Springs and Shock Absorbers
- Whirlpool Washer Switches
- Whirlpool Washer Timers
- Whirlpool Washer Transmissions and Clutches
- Whirlpool Washer Valves
- Whirlpool Washer Wheels and Rollers
- Whirlpool Washer Wire Plugs and Connectors