Whirlpool Dishwasher Pumps
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Whirlpool Dishwasher Pumps
Your Price
$70.66
In Stock
Whirlpool Dishwasher Circulation Pump
PartSelect Number PS16744934
Manufacturer Part Number W11612326
This circulation pump is a genuine OEM replacement part designed for use in dishwashers. It is responsible for circulating water throughout the dishwasher during the wash and rinse cycles. The circulation pump draws water from the dishwasher tub, pressurizes it, and then distributes it to the spray arms, which spray the water onto the dishes to remove food particles and debris. The circulation pump may fail due to several reasons such as an electrical fault, a blockage in the pump impeller, motor failure, or physical damage. A faulty pump will result in water leakages, unusually loud noises during use, reduced water circulation, and poor cleaning performance.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Samoil from COOPER CITY, FL
The dish washer wasn’t cleaning dishes
The circulation pump is a super easy fix and the installation video parts select has on its website is accurate. I felt the most difficult part of the repair was removing the dishwasher from the kitchen counter to make the repairs. After you get the dishwasher out, you pretty much just pop the old pump out with your hands and a flat head screwdriver. (The supplied video is spot on ) Installing the new pump will require a pinch plier or a hose clamp. I chose a new hose clamp as it is cheaper and I would never use the pinch pliers after this job.
Read more...
Your Price
$59.95
In Stock
Whirlpool Dishwasher Drain Pump 120v 60hz
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
PartSelect Number PS11753379
Manufacturer Part Number WPW10348269
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Andrew from Alexandria, VA
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
Your Price
$62.33
In Stock
Whirlpool Dishwasher Drain Pump
Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn and push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front. Read more...
PartSelect Number PS11738151
Manufacturer Part Number W10876537
This drain pump is for dishwashers.
Drain pump removes the water from the dishwasher tub during the drain phase of the dishwashing cycle.
Unplug the dishwasher and shut off the water supply before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
- Leaking
- Not draining
- See more...
Installation Instructions
Kelli from BURLINGTON, MA
Dish washer would not drain properly
Shut off breaker. Took off front skirt of dishwasher . Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn and push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front. Read more...
Your Price
$33.95
In Stock
Whirlpool Dishwasher Chopper Assembly
PartSelect Number PS1734917
Manufacturer Part Number W10083957
This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You may need to replace this part if your dishes are not being cleaned properly, your appliance is particularly noisy, or you are noticing draining problems. The tools you will need to make this repair include a number 20 and a number 15 torque screwdriver, a small flat blade screwdriver, and a pair of needle nose pliers.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Steve from Killeen, TX
Not cleaning top tier,all dishes not getting clean
Disassembled inside bottom section of dishwasher found broken chopper part,removed and replaced with new part,only hard part was holding spring compressed when putting in new part,needed needlenose and thin screwdriver.Thank You for your great website and help
Read more...
Your Price
$70.66
In Stock
Whirlpool Dishwasher Circulation Pump
PartSelect Number PS16744935
Manufacturer Part Number W11612327
The pump motor delivers water to the spray arms to clean the dishes during the wash cycle.
Fixes these symptoms
- Not cleaning dishes properly
- Not draining
- Will not fill with water
- See more...
Your Price
$55.39
In Stock
Whirlpool Dishwasher Drain Pump
PartSelect Number PS11756031
Manufacturer Part Number WPW10531320
This drain pump is an authentic OEM replacement part for models of dishwasher. It is responsible for removing wastewater from the dishwasher during the drainage cycle. It is located at the bottom of the dishwasher and can be accessed by removing the lower access panel or by tipping the dishwasher on to its rear side. When activated, the drain pump pushes the wastewater through the drain hose and into the household plumbing system or garbage disposal. If the drain pump malfunctions or becomes clogged, it can lead to drainage issues, resulting in water pooling at the bottom of the dishwasher, foul odors and potentially resulting in incomplete cleaning of dishes.
Fixes these symptoms
- Leaking
- Noisy
- Not draining
- See more...
Installation Instructions
Douglas from SAINT JOHN, IN
Dishwasher was making a moaning sound when draining.
Unplug dishwasher. Remove lower front accessible panel. Disconnect wires to the drain pump. Rotate pump to unlock and remove. Apply plumbers grease to rubber seal and install new pump. Connect wires. Plug in dishwasher and run rinse cycle to check for no water leak. If all okay replace access panel. Done.
Read more...
Your Price
$93.61
In Stock
Whirlpool Dishwasher Drain And Wash Impeller Kit
PartSelect Number PS382822
Manufacturer Part Number 675806
This dishwasher drain and wash impeller kit comes with both the drain and wash impeller, gaskets, chopper, and installation screw. This part helps stop your dishwasher from leaking and helps with the proper draining of the dishwasher. If you notice that your dishes are not cleaning, the dishwasher is not draining properly, or is making any unusually loud sounds or grinding noises, this could indicate the impeller and seal kit have broken down and need to be replaced. You will need a #15 and #20 torx driver, a small flat-blade screwdriver, 1/4-inch nut driver, adjustable wrench, and a small hammer and a sharp chisel.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Daniel from Sarasota, FL
leaking from tub above motor
Disconnect unit and remove from under counter. remove lower spray arm, tip over dishwasher on it's back, diconnect wires from motor , unscrew drain fitting rotate motor mounts to and lift pump and motor assembly up and out from inside the dishwasher. thoughly clean all parts during pump disassembly( under running water and a toothbrush works well) . Looking at a parts diagram,and using your memory from disassembly replace the new seals and put it all back together, with patience you can do anything and use common sense.
Read more...
Your Price
$51.41
In Stock
Whirlpool Dishwasher Drain Pump
PartSelect Number PS16221213
Manufacturer Part Number W11497943
Stay ahead of your kitchen chores with the Whirlpool Dishwasher Drain Pump. Designed to efficiently remove water from the dishwasher tub during the draining phase of your dishwashing cycle, this authentic OEM part ensures your dishwasher's optimal performance. Originally manufactured for compatibility with select models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dishwashers, it brings the constant reliability and exceptional quality you'd expect from the Whirlpool brand. Please ensure to verify your model before ordering to avoid any small variations in size or shape. Before installing this part, always remember to unplug the dishwasher and shut off the water supply for safety. Wearing work gloves during installation can also help protect your hands. Maintain the integrity of your appliance with this highly-effective Whirlpool Dishwasher Drain Pump.
Fixes these symptoms
- Not draining
- See more...
Installation Instructions
Roger from CAMPBELLSVLLE, KY
Getting codes on display E1 E9. Pump not draining. It would drain after pump cooled down.
After unplugging the dishwasher, removing the water supply hose, and disconnecting the drain hose, I removed the dishwasher from under the cabinet. I turned the dishwasher on its side, exposing the drain pump. I removed the electrical connection wire by sliding the white keeper forward and then using a small screwdriver, I pushed in on the black clip securing the plug. I then found the clip holding the pump and rotated the pump from the sump area. I installed the new pump in the same way I removed it. Reinstalled the water line, pump hose . Put unit back and plugged it in. Turned on dishwasher. Works perfectly now.
Read more...
Your Price
$75.83
In Stock
Whirlpool Dishwasher Drain Pump
PartSelect Number PS12741766
Manufacturer Part Number W11412291
Introducing the Whirlpool Drain Pump: a key component to optimize the functionality of your dishwasher. This authentic OEM part specially developed for Whirlpool is compatible with various models of Whirlpool dishwashers. Gone are the days of standing water as this dependable pump expertly removes water during the crucial drain phase of your dishwashing cycle. Before installation, remember to disconnect your dishwasher and turn off the water supply for safety reasons; gloves are encouraged to safeguard your hands during the process. Distinguished for its superb reliability, this is a Drain Pump that will notably elevate your dishwashing routine. Please always confirm that this part aligns with the specifications of your model to ensure optimum performance.
Fixes these symptoms
- Not draining
- See more...
Installation Instructions
Bruce from MADISON, MS
I was getting the F9 E1 error code intermittently then consistently.
Checked drain hose and it was clear without kinks. I shut of the electrical breaker. Verified no power to washer. Removed the lower trim panel. Lowered the adjustable feet to allow me to slide my unit out. Disconnected drain hose from unit. Pulled unit from cabinet. My drain pump is located on the right bottom side when facing the door of the unit. I did not need to lay the unit on its side and have enough power cable to not have to disconnect it while still pulling the unit all the way out of the cabinet. The pump is easily accessed from the right side hidden behind insulation. Disconnected power wire from pump. Pressed down locking latch and turned pump counter clockwise removed then replaced in opposite order. I have run 3 load’s before posting this and as of now my dishwasher is functioning perfectly.
Read more...
Your Price
$104.86
In Stock
Whirlpool Dishwasher Sump
PartSelect Number PS11755006
Manufacturer Part Number WPW10455268
This works in conjunction with the pump and filtration system. It is used to receive drainage for disposal.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Jason from MOLINE, IL
Water leaking through the sump shaft seal
First I removed everything off of the bottom of the dishwasher. Then I removed the main center piece that everything mounts to. Then I reinstalled the new center piece with the help of some evoo cooking spray (extra virgin olive oil) I sprayed it on the rubber seal to aid in getting that center piece installed without a battle. Then I reinstalled everything else in the reverse order that I removed it. The evoo cooking spray works wonders for more than just cooking !!!
Read more...
Related Whirlpool Dishwasher Parts
- All Whirlpool Dishwasher parts
- Whirlpool Dishwasher Brackets and Flanges
- Whirlpool Dishwasher Caps and Lids
- Whirlpool Dishwasher Circuit Boards and Touch Pads
- Whirlpool Dishwasher Deflectors and Chutes
- Whirlpool Dishwasher Dishracks
- Whirlpool Dishwasher Dispensers
- Whirlpool Dishwasher Doors
- Whirlpool Dishwasher Ducts and Vents
- Whirlpool Dishwasher Elements and Burners
- Whirlpool Dishwasher Filters
- Whirlpool Dishwasher Fuses
- Whirlpool Dishwasher Grilles and Kickplates
- Whirlpool Dishwasher Handles
- Whirlpool Dishwasher Hardware
- Whirlpool Dishwasher Hinges
- Whirlpool Dishwasher Hoses and Tubes
- Whirlpool Dishwasher Insulations
- Whirlpool Dishwasher Knobs
- Whirlpool Dishwasher Latches
- Whirlpool Dishwasher Lights and Bulbs
- Whirlpool Dishwasher Manuals and Literatures
- Whirlpool Dishwasher Panels
- Whirlpool Dishwasher Racks
- Whirlpool Dishwasher Seals and Gaskets
- Whirlpool Dishwasher Sensors
- Whirlpool Dishwasher Spray Arms
- Whirlpool Dishwasher Springs and Shock Absorbers
- Whirlpool Dishwasher Switches
- Whirlpool Dishwasher Trims
- Whirlpool Dishwasher Valves
- Whirlpool Dishwasher Wheels and Rollers
- Whirlpool Dishwasher Wire Plugs and Connectors