Maytag Dishwasher Hinges

Popular Maytag Dishwasher Hinges

Your Price
$33.09
  In Stock
Maytag Dishwasher Door Balance Link Kit
★★★★★
★★★★★
202 Reviews
PartSelect Number PS972325
Manufacturer Part Number 8194001
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The kit includes two door balance links and two door balance mounts with wheels, which will replace both the left and right sides. The only tool needed is a 5/16 nut driver. Before removing the existing kit, take note of how the door balance link kit is assembled for a smooth replacement process. It is recommended to check the door springs in case they need to be replaced as well.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
Installation Instructions
Scott from Fort Lauderdale, FL
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough. Read more...
Your Price
$7.49
  In Stock
Maytag Dishwasher Friction Sleeve
★★★★★
★★★★★
34 Reviews
PartSelect Number PS11745488
Manufacturer Part Number WP8268961
This part helps to keep your door quiet when it opens and closes.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Noisy
  • See more...
Installation Instructions
Arthur from YORKTOWN HTS, NY
Door will fall down after opening
unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE. Read more...
Your Price
$11.13
  In Stock
Maytag Dishwasher Door Cable Link
★★★★★
★★★★★
6 Reviews
PartSelect Number PS11747772
Manufacturer Part Number WP99003446
This is a part for your dishwasher. The door cable link helps to keep the door steady and give support to the weight of the door when it is being opened or closed. If you notice the door latch has failed or the door is not closing properly, this might indicate a need to have the door cable link replaced. To perform this repair, you will start by turning the power off from the appliance. You will need to pull the unit out of installation. To access the cables, you will need to remove the side panel. You should be able to see the cables underneath the panel once removed.
Fixes these symptoms
Installation Instructions
jeffrey from holland, PA
broken door springs
I pulled the unit from under the counter. the springs and cables are on the front sides of the dishwasher. I moved the insulation removed the broken spring and cables and replaced them with the new parts. just one side was broken, but I replaced both while I had the unit out. Read more...
Your Price
$11.09
  In Stock
Maytag Dishwasher Door Spring Linkage
★★★★★
★★★★★
16 Reviews
PartSelect Number PS11746857
Manufacturer Part Number WP912653
The door spring retainer is used in dishwashers. It attaches and holds the door spring to the support frame. If your dishwashers door keeps crashing, or both the door and dish rack are falling apart, then replacing the door spring retainer, which provides more flexibility, could be the solution to your symptoms. Before starting this project make sure to unplug the dishwasher as well as shut off the water supply before installing the spring retainer. Tools are not needed for this easy repair. Refer to the manufacturers installation instructions for best results and accuracy.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
Installation Instructions
kathleen from farmersville, CA
son used door for a step and bent as well as broke spring door component
first i removed the 2 holding screws fron the underside of the counter then oulled the dishwasher out about a foot. i then removed the side panel that hold the front plate in plase on the right, below this were the screws that held the door hinge assembly on the right. i then proceeded to remove those bolts. and replaced with the new one. replacing the spring and the linkage came next no tools required. i have to say that the diagram when i ordered helped emensly. i am a 45 yr old woman and fixed it by nyself thanks to your ordering diagrams. life is good!! Read more...
Your Price
$139.03
  In Stock
Maytag Dishwasher Door Hinge - Right Side
PartSelect Number PS11746183
Manufacturer Part Number WP8534853
Fixes these symptoms
Installation Instructions
Tom from UNION GROVE, WI
A small water leak at door
After replacing broken door cables I had a small leak at the door corner. I replaced door seal with that not fixing the leak and found that the door hinges were bent a little from the cables being broke for awile. Installed new hinges and leak is fixed now. A little difficult but once unit was pulled out about 6 inches the hinges were not bad to replace Read more...
Your Price
$24.82
  In Stock
Maytag Dishwasher Mount
★★★★★
★★★★★
1 Review
PartSelect Number PS11748211
Manufacturer Part Number WPW10084086
Your Price
$75.12
  In Stock
Maytag Dishwasher Hinge Bushing
★★★★★
★★★★★
1 Review
PartSelect Number PS11745491
Manufacturer Part Number WP8268990
Your Price
$5.81
  In Stock
Maytag Dishwasher Short Dispenser Door Retaining Pin
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11757600
Manufacturer Part Number WPY912679
The short dispenser door retaining pin latches your washing machine door to the hinge. If you find that your washing machine will not dispense detergent, or the lid will not latch properly, you may need to replace the short dispenser door retaining pin. This pin is less than one inch in diameter, and is the shorter of the two hinge pins. To find the larger hinge pin, search WP6-912678. This part is cylindrical and is made of metal. The short dispenser door retaining pin is sold individually. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
  • Door latch failure
  • Lid or door won’t close
  • Will not dispense detergent
  • See more...
Installation Instructions
richard from austin, MN
Drains but doesn't spin, door lock does not engage.
Door locked light did not come on and did not have 120 VAC across the Wax Motor. Also the Wax Motor did not extend out to make contact with the Door Lock, Spin Enable Switch. General guidance is to replace drive belt and to replace Wax Motor along with the Door Lock, Spin Enable Switches (total of two limit switches). This did not correct the problem. Checked for power and traced loss of power back to the Control Board where resistor R11 was found to be burnt out. Replaced Resistor with new Carbon Film unit, rating of 3.9 K-ohms, 1/4 W and 5%. As a prcaution, replace the Triac (manufactue part number NTE5657), component identified as Q6, rating of 0.8 Amp, 600 VAC. Semiconductor parts must be obtained from somewhere other than Parts Select (unable to find in the small town I live in, I located on the internet at Mouser.com). Unit works great now. Read more...

Related Maytag Dishwasher Parts