Kenmore Washer Doors
Popular Kenmore Washer Doors
Your Price
$101.06
In Stock
Kenmore Washer Washing Machine Door Lock Assembly
PartSelect Number PS12704713
Manufacturer Part Number W11307244
This is lid lock designed for use within various washing machines. This lid lock, also known as a latch assembly, is used to secure the lid of your washing machine during the washing cycle. If your washing machine is experiencing issues starting or if the lid is not securing, this lid lock assembly likely needs to be replaced. This lid lock attaches underneath the top portion of your washer and its wire harness connects to the rear of the appliance. To replace this assembly, you will need a screwdriver, flathead screwdriver or putty knife, and wrench. This lid lock is an OEM part that is sold individually and does not come with any other parts or accessories.
Fixes these symptoms
- Lid or door won’t close
- Locking Issues
- Will not agitate
- See more...
Installation Instructions
John from BEAVER DAMS, NY
latch switch was not working
unfasten top from back, slide top forward and lift up, remove switch and cable (one piece), in stall new switch and cable, put top down and slide back, reinstall screws.
Read more...
Kenmore Washer Exterior Door Panel - White
PartSelect Number PS3490391
Manufacturer Part Number 137265500
Fixes these symptoms
- Lid or door won’t close
- See more...
Your Price
$222.36
In Stock
Kenmore Washer Door Glass
PartSelect Number PS1145708
Manufacturer Part Number 134366400
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Gennaro from Nutley, NJ
Glass inner door cracked due to machine rocking
Simply removed several screws around inner glass Then part set right into place. replaced all the screws and was completed.
Read more...
Kenmore Washer Inner Door Frame - White
PartSelect Number PS3490393
Manufacturer Part Number 137280300
Kenmore Washer Inner Door Panel Kit - White
Next, I remove the boot from the soap dispenser tube (located at about 11:00 of the opening) with a needlenose plyers. The manual recommends flattening a 3" copper pipe to fashon a tool to release the "bread tie" fastener. I can see why but patience with a needlenose sufficed.
I pulled the boot down from the tub housing (with much force) exposing the band that holds the boot in firmly. I one pull, both pieces came out. I could tell getting the new one is was going to be a chore.
I cleaned the area and after about 40 strenuous minutes of getting the new boot onto the tub, only a couple things remained. Even with help, be prepared to dedicate hours of frustration getting the band around the boot securing it to the tub. The working space is minimal and the task is virtually hopeless to slightly possible.
Once that's taken care of, you may feel like you can accomplish anything. The rest goes up in the order it came out. Make sure you slide the boot up as far up the soap dispensing unit as possible before securing the bread tie clamp.
Run the seal around, close the door and have one of you kids clean up the work area (and mop the blood, sweat and tears from the unit and the floor. Read more...
PartSelect Number PS975857
Manufacturer Part Number 134426500
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Jon from Stevens Point, WI
Rubber seal (boot) needed to be replaced.
I began by removing the seal from the exterior lip of the machine housing. I took a razor and removed any rubber and adhesive that remained on the unit. Next, I remove the boot from the soap dispenser tube (located at about 11:00 of the opening) with a needlenose plyers. The manual recommends flattening a 3" copper pipe to fashon a tool to release the "bread tie" fastener. I can see why but patience with a needlenose sufficed.
I pulled the boot down from the tub housing (with much force) exposing the band that holds the boot in firmly. I one pull, both pieces came out. I could tell getting the new one is was going to be a chore.
I cleaned the area and after about 40 strenuous minutes of getting the new boot onto the tub, only a couple things remained. Even with help, be prepared to dedicate hours of frustration getting the band around the boot securing it to the tub. The working space is minimal and the task is virtually hopeless to slightly possible.
Once that's taken care of, you may feel like you can accomplish anything. The rest goes up in the order it came out. Make sure you slide the boot up as far up the soap dispensing unit as possible before securing the bread tie clamp.
Run the seal around, close the door and have one of you kids clean up the work area (and mop the blood, sweat and tears from the unit and the floor. Read more...
Kenmore Washer Stainless Steel Door Frame
PartSelect Number PS11748168
Manufacturer Part Number WPW10079810
Related Kenmore Washer Parts
- All Kenmore Washer parts
- Kenmore Washer Agitators
- Kenmore Washer Bearings
- Kenmore Washer Belts
- Kenmore Washer Brackets and Flanges
- Kenmore Washer Caps and Lids
- Kenmore Washer Circuit Boards and Touch Pads
- Kenmore Washer Dispensers
- Kenmore Washer Drawers and Glides
- Kenmore Washer Drums and Tubs
- Kenmore Washer Filters
- Kenmore Washer Handles
- Kenmore Washer Hardware
- Kenmore Washer Hinges
- Kenmore Washer Hoses and Tubes
- Kenmore Washer Knobs
- Kenmore Washer Latches
- Kenmore Washer Legs and Feet
- Kenmore Washer Motors
- Kenmore Washer Panels
- Kenmore Washer Power Cords
- Kenmore Washer Pulleys
- Kenmore Washer Pumps
- Kenmore Washer Seals and Gaskets
- Kenmore Washer Springs and Shock Absorbers
- Kenmore Washer Switches
- Kenmore Washer Timers
- Kenmore Washer Transmissions and Clutches
- Kenmore Washer Valves
- Kenmore Washer Wire Plugs and Connectors