Whirlpool Dryer Drawers and Glides
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Whirlpool Dryer Drawers and Glides
Your Price
$64.39
In Stock
Whirlpool Dryer Front Glide Kit
PartSelect Number PS2003584
Manufacturer Part Number 12002126
This kit includes 2 glides (left and right), 2 pads with adhesive backing and 1 support brace.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Thomas from Oneonta, NY
Dryer made a loud noise and vibrated badly
First I made sure the unit was unplugged. I popped the top of the unit with a slotted screw driver, lifted the top up and rested it against the wall behind the dryer. I removed the two screws - one on each side in front on top of the dryer cabinet. Then I tipped back the front panel of the dryer slightly with the door of the dryer closed. I unclipped the door switch with a slotted screw driver and then lifted the entire front panel including the door off of the the two floor clips on bottom. I set the front panel aside. Next I lifted the large drum slightly to dislodge the rollers in back and slid the drum back slowly while sliding the thin belt back on the drum until the drum was out of the unit and the belt was detached and loose. Then I cleaned the unit thoroughly, vacuumed all lint and dirt and wiped down the outside of the large drum with mineral spirits to make sure it was totally clean and smooth. Then I removed the two rollers and the roller shafts at the back of the unit following the directions enclosed. My slip-ring pliers came in handy to remove the retaining rings on the roller shafts. I replaced the rollers and roller shafts and the supplied washers and spacers as per the instructions. I sprayed a little WD-40 on the surface of the rollers and it stopped all squeaking and vibration of the drum. Next I replaced the front drum pads and runners as per the instructions. I then slid the drum back in place taking care to slide the new belt back around the drum in the same position as the old belt. Now came the difficult part - laying on the floor and reaching under the drum I positioned the belt around the motor shaft and tension pulley. This must be done by "feel" and must be done correctly!! Follow the instructions on the positioning of the belt very carefully and make sure it is in the correct position on the drum, motor shaft, and tension pulley! Next, get up and rock the drum up and down slightly to make sure it has engaged the two rear rollers properly. Rotate the drum manually one or two turns to make sure the belt is in the correct position. Then replace the front door panel by dropping it onto the two clips at the base of the unit and taking care to replace the door switch in reverse order of taking it out. Then replace the two screws at the top front on each side of the unit to secure the front panel. Lower the top of the unit back in place, plug in the dryer, turn it on and enjoy the lack of noise you have created.
Read more...
Your Price
$49.31
In Stock
Whirlpool Dryer Drum Glide (left Side)
PartSelect Number PS11740714
Manufacturer Part Number WP31001470
This dryer drum glide is almost six inches long and is blue in color. This glide is made of plastic and is designated for the left side of some clothes dryers. This glide is also available as part of a glide kit, part number PS177273.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Greg from Salt Lake City, UT
Dryer made noises like metal on metal grinding
Unplugged the dryer then popped the top off and tilted it back, exposing the drum. Then using a flat bladed screw driver, removed the two sheet metal screws holding the front panel on. Once the front panel was removed, I pulled the drum off, exposing the motor and worn pulley. I removed the pulley arm, then removed the pulley. The bearings were totally gone, so I replaced it with a new pulley, replaced the belt and the front drum glides, since they were obviously worn. While it was apart, I cleaned out the interior with a shop vac, which greatly improved the efficiency of the dryer.
Read more...
Your Price
$50.36
Special Order
Whirlpool Dryer Drum Glide - Right Side
PartSelect Number PS11740713
Manufacturer Part Number WP31001469
This dryer drum glide is just under seven inches long. It is all blue in color and is made of a hard plastic. This front drum support is intended for use with the right side of clothes dryers.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Greg from Salt Lake City, UT
Dryer made noises like metal on metal grinding
Unplugged the dryer then popped the top off and tilted it back, exposing the drum. Then using a flat bladed screw driver, removed the two sheet metal screws holding the front panel on. Once the front panel was removed, I pulled the drum off, exposing the motor and worn pulley. I removed the pulley arm, then removed the pulley. The bearings were totally gone, so I replaced it with a new pulley, replaced the belt and the front drum glides, since they were obviously worn. While it was apart, I cleaned out the interior with a shop vac, which greatly improved the efficiency of the dryer.
Read more...
Your Price
$111.67
Special Order
Your Price
$143.50
Special Order
Your Price
$145.48
Special Order
Your Price
$60.95
Special Order
Your Price
$81.13
Special Order
Your Price
$20.95
Special Order
Your Price
$48.24
Special Order
Whirlpool Dryer Right Side Drum Glide Pad
PartSelect Number PS11740710
Manufacturer Part Number WP31001356
This dryer drum glide is used with many dryers. It is almost three inches long, and it has an adhesive backing.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Greg from Salt Lake City, UT
Dryer made noises like metal on metal grinding
Unplugged the dryer then popped the top off and tilted it back, exposing the drum. Then using a flat bladed screw driver, removed the two sheet metal screws holding the front panel on. Once the front panel was removed, I pulled the drum off, exposing the motor and worn pulley. I removed the pulley arm, then removed the pulley. The bearings were totally gone, so I replaced it with a new pulley, replaced the belt and the front drum glides, since they were obviously worn. While it was apart, I cleaned out the interior with a shop vac, which greatly improved the efficiency of the dryer.
Read more...
Related Whirlpool Dryer Parts
- All Whirlpool Dryer parts
- Whirlpool Dryer Bearings
- Whirlpool Dryer Belts
- Whirlpool Dryer Brackets and Flanges
- Whirlpool Dryer Caps and Lids
- Whirlpool Dryer Circuit Boards and Touch Pads
- Whirlpool Dryer Dispensers
- Whirlpool Dryer Doors
- Whirlpool Dryer Drums and Tubs
- Whirlpool Dryer Ducts and Vents
- Whirlpool Dryer Elements and Burners
- Whirlpool Dryer Fans and Blowers
- Whirlpool Dryer Filters
- Whirlpool Dryer Fuses
- Whirlpool Dryer Handles
- Whirlpool Dryer Handles and Latches
- Whirlpool Dryer Hardware
- Whirlpool Dryer Hinges
- Whirlpool Dryer Hoses and Tubes
- Whirlpool Dryer Knobs
- Whirlpool Dryer Latches
- Whirlpool Dryer Legs and Feet
- Whirlpool Dryer Lights and Bulbs
- Whirlpool Dryer Manuals and Literatures
- Whirlpool Dryer Motors
- Whirlpool Dryer Panels
- Whirlpool Dryer Power Cords
- Whirlpool Dryer Pulleys
- Whirlpool Dryer Seals and Gaskets
- Whirlpool Dryer Sensors
- Whirlpool Dryer Springs and Shock Absorbers
- Whirlpool Dryer Switches
- Whirlpool Dryer Thermostats
- Whirlpool Dryer Timers
- Whirlpool Dryer Trims
- Whirlpool Dryer Valves
- Whirlpool Dryer Wheels and Rollers
- Whirlpool Dryer Wire Plugs and Connectors