JGD8130ADB20 Jenn-Air Cooktop - Instructions

Two screws inside the exhaust box to take out the switch assembly and 2 nuts on the switch. Nothing to it

Remove switch cover with two screws ,remove two nuts holding switch in place ,remove switch,then reverse procedure with new switch.

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

Disassembled old part put new one in reversed order

Flip the breaker. Lift off the fan center grate. Remove two screws located on back of the burner dials housing. Lift the back of the housing, then pull this gently away from the front to unhook the front. Turn this over, locate the switch. Pull the three electrical plug connections from the switch plastic housing, remembering their locations. Back off the two nuts holding the switch to the underneath side of the dials housing. Place the new one in place, put it all back together.

remove two nuts and install new switch, then change wire connections from the old switch to the new one.
Then place it back together.

Removed Stove cartridge from stove-top.

Unfastened bottom screws, I recall 6.

Removed cover.

Removed two screws to igniter.

Used needle nose pliers to remove connectors x 2.

Had to drill to enlarge the mounting screws to new ignitor, then screwed it in place

Connected the two wires to each igniter.

Replaced cover n screws.
Reinstalled cartridge.

Bingo

First I did was to google the problem I have. There several video how to solve the problem. It show me different ways to solve my problem. I just follow the instructions. Thank to google without it, I am lost. I may add, that google is a big saver for me.

Prepare a flat area with newspaper, a screwdriver, and a small bowl for the screws, and a small wire brush (if you want to clean as you go). I also recommend taking photos as you proceed, for reference.

ALSO, take close note of the orientation of the cook top base, one end has a lip that's allows for burner assembly removal.

Remove entire two burner assembly, place upside down on newspaper, remove seven Phillips screws, remove assembly bottom.

Remove small screws from gas tubes, pay close attention as you remove the gas tube from the bottom of the burner, to the orientation of the two washers (the washers have an edge).

Remove the burner tubes and washers.

Carefully remove the igniter connectors from igniter.

Remove the end of the assembly.

Grasp the burners, and turn to rotate the burner to a position where the "bumps" on the burner match up with the gaps in the burner cook base. Remove the burners.

The old burner base can be set to the side. At this time i cleaned the burners throughly with a small toothbrush size wire brush.

Assemble the burners to the new top base by aligning the bumps to the opening in the cook top base, turn slightly to keep burner in place. Insert the gas tubes, with the washers (be careful about the washer lip orientation) with the smaller screws, do not overtighten!

Attach the igniter connector to the igniters.

Align the burner/gas tubes with the assembly end. Carefully set the base into place, adjust the tubes as necessary to get the screws aligned with the holes. Install the screws, tighten hand tight.

Install entire assembly into cook top, check igniter and burner operation.

Glass cleaner is great for cleaning the new porcelain surface.

Remove the 2 burner assembly by gently lifting the rear burner and pull towards the back of the stove and the entire 2 burner assembly will slide out. Turn assembly up side down, remove all the screw on the cover with a philip screwdriver and remove cover. Once opened, you will see the ignighter, remove the 2 screws holding it in place, remove and replace the ignighter and secure with two screws. Follow the 2 lead wires and remove and replace with the new wires, simply pull off old and push on new wires. Replace the cover and all the screws, slide it back onto the stove and you will have ignition! Simple install, takes about 20-30 minures. If both burners are out, this is probably the problem. If only 1 burner is out, you probably need to replace the stove burner spark.

Make sure all burners on stove top are off.Half twist burner top to separate burner from stove top.The burner slide fits over the metal tube that transports the gas to the burner.Remove the 2 slip fit connected wires from the underside of the burner.They should be of different sizes so no worries about incorrectly re-attaching them.The igniter has 2 philips screws holding the igniter to the burner, Remove those and the igniter will be able to be removed with a little wiggling.Insert new igniter thru the hole in the burner and secure with the 2 screws. Reattach wires , place burner back on top making sure the wires aren't being crimped when the burner slides over the aforementioned metal tube and twist burner to seat in stove top, turn on burner to confirm igniter now ignites properly.

UNPLUG THE POWER CORD! This particular model is a (slide-in) unit, it was wedged between to fixed cupboards/cabinets. Therefore, there are really no side panels to speak of, this made the repair slightly easier. I simply slid the unit out enough to unplug the power cord and access the right side of the unit. All one needs, at this point, is a Phillips head screw driver to remove a small metal panel installed just below the stove top panel (right side of range), its held with approx. 8 screws. There is one other panel that must be removed as well, (you may want to remove this panel first). It is an enameled-like panel approx. 5" wide x 36" long located at the front of the range (right side) running the length/height of the range (held with 2 screws). Get those 2 panels removed and you will see the spark module attached near center of range just under stove-top panel. Module is attached to a small metal bracket, module has 6 wires attached to it (2 feeding the module and 4 exiting the module to the burners). Bracket screws are nearly impossible to get at (you need a very stubby Phillips screw driver, if you can even get your hand in there). Anyway, I simply released the module from the bracket, then carefully bent the bracket back toward me; to provide work area for my hands. The bracket bends easily and really can't be broken. Now, at this point (using longer needle-nose pliers) detach the wires from the old module (remembering each wires location) or, as I did, hold the replacement module near the existing module and transfer the wires one at a time. Now, slap it all back together as you took it apart. Really simple job, total time is easily/generally under 30 minutes. It may be easier to access the module by removing all the burner components and raising the stove-top? Not sure? I chose not to do the repair that way. Hard part was locating where the manufacturer hid the module on the range. :- ) D.I.Y.ers Rock!!!

throw breaker, unbolt switch, unplug leads, rerplace switch, bolt in place, reattach leads, turn breaker back on

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

Turned off power to range top. Two screws to lift the control area. One snap on was burned off.
Removed tab from inside same. Used nut driver to remove switch. Taped wires and restored control area. Power back on. Went to computer and got website for Partselect. Found description of part got me to several choices. The range is 25 years old. Selected a switch that seemed close. It arrived in two days. Redid the same steps. Some file and drill work required to make switch fit. Screwed switch in place. Untaped snap connectors and attached to switch. Checked for function and and restored control area.