CTS17RBSERWW General Electric Refrigerator - Instructions

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

Emptied the lower area of food, removed the drawers and the removed the broken shelf frame. My glass was unbroken so after removing it from the broken frame and cleaning it, I just had to place it in the new frame and put it in the frig. Can't believe how easy and quick the whole process was. I can now utilized all that wasted space in my frig again.

removed food from freezer section removed fan guard, partially remove ice maker, remove back panel, then fan assembly,disaasembled fan motor from brackets, fan from motor, grommet from bracket. assembled grommet in bracket, fan blade on motor, motor in bracket, fan assembly back in compartment, installed back panel,then ice maker, replaced fan guard and food. no more noise.

Just snapped in.

Took out old put new in. Watched a u tube, no problems

Removed old replaced with new part. Easy Peasy

I replaced the fan motor and one of the grommets. When I took the motor out it was clear it was failing because there were metal flakes from the motor on the fan blade. I followed the instructions on the posted video. My model did not have a removable bottom tray in the freezer so that was one less thing to do. Aside from that the video was accurate. I had two minor problems during reinstallation. First, it was very difficult to get the spring clamp back on the fan blade without pushing it against the motor. Recommend you get someone to help hold the spring open while you push it on. Second, the length of wire on the replacement was not exactly the same as the original and I had to move some wires around. Recommend you take a picture of the cable layout before disassembling.

a-ok. no problems

Remove power from the unit. With short length #2 Phillips loosen and remove the two(2) screws on the control panel located center top of the refrigeration area. Slide the control panel back about 1/2 inch and allow it to dangle from its wiring harness. Pinch the locking tab on the harness connector with one hand and use the other hand to separate the two sides. A little force is required. Remove the control panel from the refrigerator and shut the refrigerator door. Examine and note the routing of the temperature probe (Silver colored flexible wire) take a picture for later reference. Remove the old and replace with new unit. route temperature probe like the replaced unit. Reverse the steps and reinstall the control panel. It is a good idea to also purchase and replace the defrost timer.

1) TURNED POWER OFF FROM REFRIGERATOR 2) REMOVED THE FREEZER SHELF FIRST BY GENTLY TAPPING THE LEFT SIDE UP AND OUT THEN THE RIGHT SIDE UP AND OUT 3) REMOVED THE 2 PHILLIPS SCREWS HOLDING THE EVAPORATIVE FAN COVER IN PLACE 4) GENTLY PUSHED THE COVER UP AND MAKING SURE THE 2 CLIPS WERE NOT DAMAGED 5) VERY GENTLY PUSHED UP ON THE STYRO FOAM SHIELD GRASPING IT FROM THE BOTTOM, BE VERY CAREFUL NOT TO CRACK OR DAMAGE THIS 6) THEN REMOVED 4 OF THE PHILLIPS SCREWS HOLDING THE BACK PANEL 7) THEN REMOVED THE 2 SCREWS HOLDING THE FAN MOTOR IN POSITION ON THE BACK COVER AND LAID THAT ASIDE 8) I COULD THEN SEE THE MOTOR SO I UNCLIPPED THE RED/DARK WIRE CLIP FROM THE HARNESS WITH MY FINGERS, THEN TOOK MY NEEDLE NOSE PLIERS AND GENTLY PULLED UP ON THE GREEN GROUND WIRE 9) I THEN REMOVED THE 2 PHILLIPS HEAD SCREWS HOLDING THE MOTOR BRACKET TO THE WALL OF THE FREEZER 10) THEN REMOVED THE ENTIRE MOTOR AND PUT THAT ON THE KITCHEN TABLE 11) TOOK MY NEEDLE NOSE PLIERS AND VERY, VERY GENTLY PRIED OFF THAT LITTLE METAL RING HOLDING THE FAN BLADE ON (TRICKY SO LEFT UP GENTLY)...I BOUGHT ADDITIONAL IN CASE I DAMAGED IT 12) TOOK MY 5/16 NUT DRIVER AND UNSCREWED THE TOP METAL BRACKET HOLDING THE MOTOR 13) LIFTED THE MOTOR OFF AND LOOKED AT THE TOP AND BOTTOM GROMMETS TO SEE IF DAMAGED OR CRACKED (I BOUGHT ADDITIONAL GROMMETS IN CASE THEY WERE CRACKED OR DAMAGED, EASY FIX) 14) THEN ATTACHED THE NEW MOTOR AND BASICALLY SIMPLY DID EVERYTHING IN REVERSE TO INSTALL THE NEW MOTOR. MAKE SURE YOU KEEP YOUR SCREWS IN ORDER SO YOU CAN IDENTIFY WHICH PART THEY CAME FROM. MAKE SURE YOU DO NOT PINCH AND WIRES WHEN RE-INSTALLING THE MOTOR. SAVED ME A REPAIR PERSON CALL.

To remove the temp sensor.2 Phillip head screws not remove the cover inside fridge .the temp control knob cover.removed that and unplugged switch.installed new switch.reinstalled cover.

Took the bracket out of box and install it like the video showed me..very easy to install..

Replace temperature control. That fixed it. Also, removed plastic bag obstructing air vent in freezer which added performance. Fridge works good now.

Click shelf into place!

Removed the door by removing the two screws holding it on. Do not try to do this repair with the door attached. Easily removed the old gasket. Getting the new one on the door was EXTREMELY difficult. I couldn't do it. After 90 minutes, I gave up and called my appliance repairman. When he arrived, he and I worked together to get the new gasket on the door. It took 2 sets of hands to do this. It still took us about 40 minutes. My repairman had a few choice words about the design of the system holding the gasket on the door. Ditto for me. So the cost of my repair was doubled because I had to pay the repairman to help me attach the new gasket. I should have just bought a new fridge.