58715203800 Kenmore Dishwasher - Instructions

Took the old out and placed the new in its place. That simple!

Simply took the old one out, and put the new one in.

First of all, I got the part 24 hours after I ordered it. That in it self was a feat. Second, I followed everyone elses instructions, pulled the old gasket out with a pair of needle nose pliers, cleaned the area as good as I could, found the notch for the slot on the gasket to slide into and viola...it slid in and stayed in. No more leakage whatsoever! Thanks for all of the tips!

Removed old hose and went to install new hose from Part Select. Part received was not the same as advertised. It was 6-8 inches shorter than the original hose. Would not make the necessary turns because of shorter length. I even went to Video instruction on installation even though I have been in Machine repair for 30 years , this video showed using the shorter hose and when installed in the video hose also had a kink because of hose length. Had to stop repair and go to hardware store and purchase a longer hose. This purchased hose from the hardware was 50% cheaper and actually worked. I also paid for 2-3 day shipping and received part 7 days later. I am very disappointed with Parts Select and am an owner of an Equipment Rental Facility and will never utilize Parts Select again.

Seriously very easy. Took screws from side of door on inside of washer, silver cover plate came off and was simple to replace the latch using torque screwdriver and phillips screwdriver.

I removed the access panel using a nut driver. One fastener on each side at the lower front panel. Move the two piece lower panel and set aside. Locate the broken spring. It will be on the floor under the dish washer. Remove the broken spring. Place the new spring end in the hole in the chord end and place the chord over the plastic guide. Use a pliers to stretch the spring and fasten it to the hole in the lower dishwasher frame at the back of the dishwasher. Check the door for proper tension. Replace the lower panel and secure with the two screws. I recommend replacing both springs at the same time to insure proper balance. If you only replace one spring you will be replacing the other in the near future.

Ordered the rack and basket.for 122$ Basket never received . Did not get my money back for a basket. Was planing to return the rack, but easy return will cast me 82$. Keep in
Never buy anything from this company

Arm screwed on and immediately fixed the problem.

if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.

the remove was very easy just with pliers and a screw drive I was able to remove the pump. Make sure the electric is off!

The drain pump was making a high pitched buzzing noise which told us that its days were numbered. When I ordered the pump I found out that the dishwasher was really made by Electrolux for Whirlpool. Taking the pump off was a simple matter of removing two hose clamps and prying the pump off the frame. The hard part was realizing that it just pulled off without damaging anything. The new pump easily slipped right in and the screw in hose clamp was easily installed. However, the hose clamp that required pinching with the pliers was not that easy. I had to use a screwdriver to push it all the way on while holding the clamp open with the pliers. All in all pretty easy.

Pulled off the old gasket and replaced it the same way with the new one.

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.

Used pliers to pull out the old gasket. New gasket snapped into place. Notice where notches in the gasket are when the old one is removed, so the new one can be properly oriented. It was not necessary to remove the door.

Remove kick plate. Pump is right up front. Disconnect the two wire from the pump. MAKE sure u have removed all water from dishwasher! There will be a little left in the pump but nothing to worry about. Next on the top of the pump there is a hose clamp. Loosen it and remove the hose. Now use pliers to slide the hose clamp off the lower hose that hooks to the dishwaher. Use a flat head screw driver to push the tabs on the white clip over and pull off the pump. Now just do this in the reverse order. Approx time: 10 minutes