58715203800 Kenmore Dishwasher - Instructions

Removed front of door to see how gasket was installed. removed door for proper cleaning of gasket area, removed old gasket cleaned area and installed new gasket in holder notch, reinstalled door adjusting alinement, reinstalled door front.

After turning of the power to dishwasher, I opened the door took of the two bottom screws on both sides of door. Closed the door and front panel just slide off. Then I took a picture of the dispenser to make use I could figure out how to put the wiring back together. Removed the six screws holding it in place and popped the dispenser out. Easy .. popped new dispenser in and lightly put all six screws back in ,wired it back up after checking my photo. Closed the door ,slid front panel back on opened the door put the 4 screws back in that hold the front panel .Turned power back on and Boom!! All done.. Not bad for a girl...

Very, very easy. Pop off the old wheels and snap the new ones into place on the rack.

Removed 6 screws from door front panel. Removed two wiring connectors and screws fromdoor latch Replaced and all is great

The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.

Watched your video repair was easy.

Remove Phillips head screws on inner part of door panel. Pull door cover up and remove face panel. Remove torx head screws from inner side of door and remove control panel. Remove two torx screws retaining door latch mechanism. Remove and replace two wiring harnesses from old latch to new latch noting polarity. I tall new latch using two original torx screws. Replace control panel and cover in reverse order. Test door latch function under any cycle. Washer should start with door closed and stop when opened

First I removed two screws that held the door panel on. Then I pulled out the old gasket, inserted the new one, replaced the door and screws and it was done! We tested the dishwasher and no more leaks!

For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!

After several years of use and cleaning the small "nubs" that held the locking peice on the assembly under the jet arm had worn off. This allowed the whole thing to spin and the dishes weren't getting clean. Finding the part on the site was easy, it arrived amazingly fast and all is up and working great. I have used Parts Select 2 or 3 times in the past and have always had the same great results. Saved me a bunch in repair bills. Thanks

I ordered the wrong part ( lower arm ) it came the next day. I than ordered the right part ( middle arm ) again next day. I decided to change both ,they just popped in. The dishwasher works like new. Great people great service.

If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.

removed the screws holding the door together, then removed the screws holding the dispenser to the interior door. replaced the wires and put the door back together

I pulled the dishwasher from the cabinet and tilted the unit back so I would have better access to the drain pump. I then removed the hose clamp from the drain hose attached to the pump and removed the hose to let drain into a container. After disconnecting a white and purple wire from the pump and removing the rubber coupling I was able to remove the pump from the housing. Installed the new pump and started the wash cycle and the pump started it's drain cycle which was a relief. Easy fix and great parts!

We ordered new upper and lower racks from PartsSelect. We returned the parts. Best part of our order was the help PartsSelect gave us to assist in the return. Everything we needed was included in the order. Our money was refunded immediately. Good company.