KitchenAid Dishwasher Valves
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular KitchenAid Dishwasher Valves
Your Price
$52.45
In Stock
KitchenAid Dishwasher Inlet Valve
PartSelect Number PS12578165
Manufacturer Part Number W11175771
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Melissa from AIKEN, SC
Inlet valve wasn't working
Put thread tape on threads. Screwed water hose to part. Pushed hose onto part. Pushed electric clip to part. Screwed part onto washer. Done
Read more...
Your Price
$52.42
In Stock
KitchenAid Dishwasher Water Inlet Valve
PartSelect Number PS16217908
Manufacturer Part Number W11434044
The water inlet valve assembly is a crucial component of dishwashers that controls the flow of water into the unit. This genuine OEM replacement part includes the inlet valve, inlet hose, and hose clamp to ensure the proper water supply for your dishwasher’s operation. Designed for specific models, this part ensures that water is fed into the dishwasher during the wash cycle, promoting efficient cleaning. Before installation, it is important to unplug the dishwasher and turn off the water supply to avoid any accidents. Wear work gloves for your safety during the installation process. Be sure to verify the compatibility with your dishwasher’s model number, as similar-looking parts may have slight variations in size or design.
Fixes these symptoms
- Leaking
- Will not fill with water
- See more...
Installation Instructions
Joseph from BIRMINGHAM, MI
Inlet valve leaking at water connection
The valve has a plastic fitting to attach the the water line with a hose fitting. Was not carful enough with the original and damaged it attaching the water line. Ordered a replacement fitting. While it is possible to replace the water inlet valve without pulling the dishwasher out from the cabinet found it was easier to get at with the machine out. The video does and good job of showing the removal and replacing the valve. Easy job, don't be like me and be careful attaching the water line.
Read more...
Your Price
$52.42
In Stock
KitchenAid Dishwasher Water Inlet Valve
PartSelect Number PS11749213
Manufacturer Part Number WPW10158389
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
MICHELLE from EDEN VALLEY, MN
water leaking out of bottom of machine
removes the 1 screw that held the old one in and removed the water lines the supply line with a adjustable wrench and the internal line had a hose clamp on it then i just went in reverse...
Read more...
Your Price
$51.43
In Stock
KitchenAid Dishwasher Water Inlet Valve
PartSelect Number PS11752927
Manufacturer Part Number WPW10327249
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Robert from E GRAND FORKS, MN
High pitched noise when the washer filled at the beginning of the cycle.
Watched the video, it went as advertised. Easy repair and the noise is gone.
Read more...
Your Price
$50.44
In Stock
KitchenAid Dishwasher Water Inlet Valve
PartSelect Number PS8760080
Manufacturer Part Number W10648041
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Bruce from GRANDVIEW, MO
Your Price
$70.99
In Stock
KitchenAid Dishwasher Water Inlet Valve
I rolled the dishwasher from under the counter and removed the water supply line from the elbow at the bottom of the dishwasher inlet valve with an adjustable wrench. We then set the dishwasher on its back to gain easy access to the inlet valve.
To remove the inlet valve, Using a philips head screwdriver I removed the one screw holding the bracket and the valve was loose from the dishwasher. Then, two wires were removed from the valve by sliding the clips from the tabs on the valve. The hose that carries the water to the dishwasher was removed by squeezing the clamp with pliers and sliding it onto the hose and pulling the hose from the nipple.
With the valve removed from the dishwasher, the elbow for the supply line can be removed from the bottom of the old valve and installed on the new valve using teflon tape to seal the connection.
The new inlet valve was then installed by reversing the procedure.
Checked to make sure there are no leaks and the dishwasher was good as new. Read more...
PartSelect Number PS11746141
Manufacturer Part Number WP8531669
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve will open and close according to the desired amount of water needed.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Claudia from Avella, PA
After removing our dishwasher from storage and installing it, the inlet valve was leaking.
After removing the kickplate covers from the bottom front of the dishwasher by removing the 2 screws that attached the covers I determined the inlet valve was leaking, I turned of the water and disconnected the electricity from the dishwasher.I rolled the dishwasher from under the counter and removed the water supply line from the elbow at the bottom of the dishwasher inlet valve with an adjustable wrench. We then set the dishwasher on its back to gain easy access to the inlet valve.
To remove the inlet valve, Using a philips head screwdriver I removed the one screw holding the bracket and the valve was loose from the dishwasher. Then, two wires were removed from the valve by sliding the clips from the tabs on the valve. The hose that carries the water to the dishwasher was removed by squeezing the clamp with pliers and sliding it onto the hose and pulling the hose from the nipple.
With the valve removed from the dishwasher, the elbow for the supply line can be removed from the bottom of the old valve and installed on the new valve using teflon tape to seal the connection.
The new inlet valve was then installed by reversing the procedure.
Checked to make sure there are no leaks and the dishwasher was good as new. Read more...
Your Price
$48.95
In Stock
KitchenAid Dishwasher Water Inlet Valve
Removed one screw holding the inlet valve to the side rail of the dishwasher. It was attached to the hot water line and then the washer water input line. Removed the electrical connector..Pull straight off, and use a pair of pliers to open the squeeze clamp on the washer hose. The hot water supply hose has a brass fitting to loosen and remove.
Replaced the inlet valve, reconnected the electrical and also replaced the hot water line from under the sink to the washer. Used a new braided 5' hose with fittings. Used teflon tape on the screws and did not over tighten the brass fittings.
Turned on the hot water supply and checked for leaks. Operated the washer and checked for leaks. Replaced the lower covers. Read more...
PartSelect Number PS11730996
Manufacturer Part Number W10844024
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed. NOTE: As per the manufacture this part has been updated from the original part. It may be a different color, and you may need to order an elbow (# W10685193) for the new designed valve to work.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
David from Lexington, NC
Inlet valve was leaking from crack in brass fitting
Removed the lower panels from beneath the dishwasher door. 4 screws. Turned off the water.Removed one screw holding the inlet valve to the side rail of the dishwasher. It was attached to the hot water line and then the washer water input line. Removed the electrical connector..Pull straight off, and use a pair of pliers to open the squeeze clamp on the washer hose. The hot water supply hose has a brass fitting to loosen and remove.
Replaced the inlet valve, reconnected the electrical and also replaced the hot water line from under the sink to the washer. Used a new braided 5' hose with fittings. Used teflon tape on the screws and did not over tighten the brass fittings.
Turned on the hot water supply and checked for leaks. Operated the washer and checked for leaks. Replaced the lower covers. Read more...
Your Price
$45.12
In Stock
KitchenAid Dishwasher Drain Check Valve With O-ring
PartSelect Number PS382661
Manufacturer Part Number 675238
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Lewis from Portsmouth, NH
Dishwasher Not Draining
Ordered both drain & wash impeller kit and the drain check valve with o-ring. Decided to test the cheaper drain check valve first. Pulled dishwasher out from wall & adjacent cabinetry; removed drain hose from disposer and drained as much water as possible; "jacked" side of dishwasher to gain access to drain hose and drain check valve; used pliers to remove hose clamp; placed flat pan underneath to catch remaining water drainage; unscrewed drain check valve; tested under bathroom faucet--determined faulty; replaced with the new one, restored connections, reset dishwasher in proper location; voila--fixed! Plan to return the unneeded impeller kit.
Read more...
Your Price
$81.03
In Stock
Your Price
$93.50
In Stock
KitchenAid Dishwasher Water Inlet Valve
I disconnected the electrical connections on the water inlet valve. I then removed the panels from the lower part of the dishwasher, I pulled the water inlet line off and then the water return line off.
I replaced the valve. The only problem I ran into is that the inlet portion required a new brass "ell" - the one that was on the old piece would have of course been ok, however, it was solidly in place in the old water inlet valve
the only other issue, and one that would probably be commonly encountered - when I first went to turn off the water supply to the DW, the valve leaked - I was fortunate to be able to take the valve apart, clean it and put it back in place Read more...
PartSelect Number PS11742317
Manufacturer Part Number WP4171000
This valve replaces old two coil valves. The attaching solenoid on the valve open and close according to the desired amount of water needed.
Fixes these symptoms
- Leaking
- Will not fill with water
- See more...
Installation Instructions
Joseph from Raleigh, NC
dishwasher not washing well
I turned off the CB for the DW and the water supply to the DW.I disconnected the electrical connections on the water inlet valve. I then removed the panels from the lower part of the dishwasher, I pulled the water inlet line off and then the water return line off.
I replaced the valve. The only problem I ran into is that the inlet portion required a new brass "ell" - the one that was on the old piece would have of course been ok, however, it was solidly in place in the old water inlet valve
the only other issue, and one that would probably be commonly encountered - when I first went to turn off the water supply to the DW, the valve leaked - I was fortunate to be able to take the valve apart, clean it and put it back in place Read more...
Related KitchenAid Dishwasher Parts
- All KitchenAid Dishwasher parts
- KitchenAid Dishwasher Brackets and Flanges
- KitchenAid Dishwasher Caps and Lids
- KitchenAid Dishwasher Circuit Boards and Touch Pads
- KitchenAid Dishwasher Dishracks
- KitchenAid Dishwasher Dispensers
- KitchenAid Dishwasher Doors
- KitchenAid Dishwasher Ducts and Vents
- KitchenAid Dishwasher Filters
- KitchenAid Dishwasher Fuses
- KitchenAid Dishwasher Handles
- KitchenAid Dishwasher Hardware
- KitchenAid Dishwasher Hoses and Tubes
- KitchenAid Dishwasher Insulations
- KitchenAid Dishwasher Latches
- KitchenAid Dishwasher Lights and Bulbs
- KitchenAid Dishwasher Manuals and Literatures
- KitchenAid Dishwasher Motors
- KitchenAid Dishwasher Panels
- KitchenAid Dishwasher Pumps
- KitchenAid Dishwasher Seals and Gaskets
- KitchenAid Dishwasher Spray Arms
- KitchenAid Dishwasher Springs and Shock Absorbers
- KitchenAid Dishwasher Switches
- KitchenAid Dishwasher Wheels and Rollers
- KitchenAid Dishwasher Wire Plugs and Connectors