Kenmore Refrigerator Legs and Feet

Your Price

$10.45

Kenmore Refrigerator Foot Brake

★★★★★

2 Reviews

PartSelect Number PS11748978

Manufacturer Part Number WPW10141622

Introducing the Whirlpool Refrigerator Leveling Leg. This genuine OEM part supports your refrigerator, ensuring it remains stability and level. The height of the leveling leg can be adjusted to suit your unique refrigerator model, providing you with versatility and customization. This leveling leg is compatible with some models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef fridges. For a smooth installation, we recommend wearing work gloves to protect your hands. Verify your model compatibility before purchase.

Installation Instructions

Daniel from BOCA RATON, FL

Original bracket foot brake screw hole was stripped and foot brake would not extend

The repair seemed simple, I just needed to remove the old bracket -- 4 screws -- and slip the new one on.

The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, I needed to shim up the side of the fridge that I was working on.

To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet. Read more...

Videos!

Your Price

$32.95

Kenmore Refrigerator Adjustable Leveling Foot - Black

PartSelect Number PS425733

Manufacturer Part Number 216396900

This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to the floor or wobbling, it may indicate that the levelling foot needs to be replaced. You will need pliers and a block of wood to perform this task. There will be one adjustable foot found in the package. Lift the dryer and place the wood to keep it propped up. You may need to use the pliers to remove the old foot. Screw the new foot into place using your hand. Once the new leveling foot is in place, lift the appliance and remove the block. Test the machine out to ensure it is now sitting level.

Videos!

Your Price

$16.95

Kenmore Refrigerator Leveling Leg

PartSelect Number PS298690

Manufacturer Part Number WR2X7877

Your Price

$36.77

Kenmore Refrigerator Leg Adjustment Assembly

PartSelect Number PS11759970

Manufacturer Part Number 4779JA3001H

Your Price

$21.82

Kenmore Refrigerator Leg Assembly

★★★★★

1 Review

PartSelect Number PS3523585

Manufacturer Part Number 4779JA3001E

Your Price

$62.73

Kenmore Refrigerator Spigot

PartSelect Number PS11740265

Manufacturer Part Number WP2305235

Your Price

$21.82

Kenmore Refrigerator Leg Assembly Adjust

PartSelect Number PS7788214

Manufacturer Part Number AFC73349801

Your Price

$44.05

Kenmore Refrigerator Leveling Leg

PartSelect Number PS557020

Manufacturer Part Number 8193716

Leveling leg Now includes two different sizes. Use the one for your model. If you need two legs you will need to purchase a QTY of two of this kit.

Installation Instructions

Phil from Fairfax, VA

Water was leaking.

This unit was unique that whole motor assembly was held in its place by two plastic clip. The gasket had few rings that worked as place holder, although gaskets don't go bad often this model could be if it gets pulled alot and if motor assembly get pushed it will push up the gasket and cause a leak. Repair was simple, 1) take spray arm off from inside. 2) get under neath the dishwasher, take off wires so it would free up some room, pulled two plastic holder out, gently push the motor assembly up to the tub, 3) from inside the tub, pull up the assembly enough to get your hand under the gasket and pull them off. 4) Replace the gasket, align the assmebly and push down to snap in the gasket. 5) get under and push in two plastic clip back in, put wires back into its place. Back in the tub to push down the assembly again to make sure there are flush with surface. Put spray arm back on. Finished. Read more...