Jenn-Air Cooktop Igniters

Videos!

Your Price

$27.95

Jenn-Air Cooktop Top Burner Igniter

★★★★★

22 Reviews

PartSelect Number PS2082000

Manufacturer Part Number 74004053

This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, element does not heat, or gas igniter glows but does not light, replacing the igniter can solve these issues. For this installation, you will need a Phillips screwdriver and needle nose pliers. First place the grate on top of the burner, then lift the burner and disconnect the wires. Next remove the two Phillips screws from the bottom of burner, pull igniter out of the burner and wiggle in the new one. Refer to the installation instructions provided by the manufacturer for more instructions.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

roy from East Providence, RI

gas burner ignitor failure

Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order. Read more...

Your Price

$28.95

Jenn-Air Cooktop Burner Electrode

★★★★★

13 Reviews

PartSelect Number PS11744318

Manufacturer Part Number WP74009336

This is a burner electrode for your oven, range, or stove. This part has a male spade. It helps your burner ignite by creating a spark, producing a flame, and lighting the surface burner. If your burner will not heat properly, you may have to replace the burner electrode. Your electrode is located under your burner. This is an OEM replacement part that will be sourced from the genuine manufacturer. This part measures less than 1.5 inches long. It is sold individually. If you need a wire lead to complete your repair, you can purchase them locally.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Dennis from Iredell, TX

Simple to change, but you do need a torx bit screwdriver.

Remove screws holding burner down, invert and remove screw in igniter. Reverse to reinstall. Read more...

Your Price

$33.95

Jenn-Air Cooktop Range Surface Burner Spark Igniter

★★★★★

9 Reviews

PartSelect Number PS11746068

Manufacturer Part Number WP8523793

This Whirlpool Surface Burner Spark Igniter is a genuine, OEM part that readily ignites the surface burner on your range. Specially designed for perfect compatibility with certain Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef ranges, ovens, and stoves. This spark electrode is a key component in producing the spark that lights the surface burner for your cooking convenience. Prior to installation, ensure your range is unplugged and gas supply is shut off. For protection, please wear work gloves during installation. Enjoy the reliability and efficiency of Whirlpool with this Surface Burner Spark Igniter.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Daniel from Needham, MA

spark igniter was weak and not lighting the flame.

Open top oven door and remove the 2 front screws which hold the burners and controls to the frame. DO NOT lift the burners more than an inch or so to look inside. You WILL bend the gas lines in the back if you do. Pull out stove from the wall, shut off gas supply and disconnect hose if needed to have room to work. Remove top back panel and remove the 3 wires connecting the top burner assembly and also remove the 2 gas lines. Now you will be able to remove the burner assembly safely. Flip it over and try to unscrew the screw holding the igniter. When you fail, drill it out and get a small metal screw to replace it. The metal is soft and the screw is hard, so drill carefully. The rest is easy, put in the new igniter and screw. and put it back together. Read more...

Your Price

$22.02

Jenn-Air Cooktop Surface Igniter

PartSelect Number PS11727815

Manufacturer Part Number W10833887

Installation Instructions

Ronald from ROSEVILLE, CA

Surface ignitor not working on one burner

Disconnect power and turn off gas. Remove all grills, knobs and burners. Under the burners are 2 Phillips head screws. Remove all 10 screws. Remove surface plate. Remove the one igniter with problem. There is a small metal clip holding it in place. Remove the wire. Install new ignitor and reverse all steps above. Read more...

Your Price

$59.20

Jenn-Air Cooktop Spark Igniter Set

★★★★★

8 Reviews

PartSelect Number PS11744110

Manufacturer Part Number WP74005890

This part provides the spark to the burners.

Fixes these symptoms

Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Patricia from Overland park, KS

Spark igniter out

The primary spark igniters failed. Take the (small) screws out of the sides and bottom of the pan. The front of the pan must be removed from the bottom, because the front burner igniter wire is too short to allow reassembly once attached. Only other is the screws for the attachment bracket are larger than the holes. Suggest routing them out slightly to get them to grip the screws. Otherwise it is quite simple. Pull the connections with a needlenose and press the new wire connection back on firmly. Screw the screws back in the pan. Read more...

Your Price

$51.42

Jenn-Air Cooktop Spark Igniter

★★★★★

5 Reviews

PartSelect Number PS11744544

Manufacturer Part Number WP7432P109-60

This part creates the spark that lights the gas and starts the burners.

Fixes these symptoms

Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Bill from Pearland, TX

would not stop igniting even after fire was on

unplugged unit from wall, disconnected gas line, and untaped the vent. disconnect the control knobs and unplugged and removed the control unit from the main unit. pulled the main unit out from the countertop and set it on a table. disconnect the burners and spark iginiters from the main unit. undo screws holding chrome brackets and stove base, to access iginiter. disconnect wiring from igniter and the one screw, replace iginiter. reverse everything to re-install Read more...