Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 4 at 11:59pm EST.
Inglis Washer Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Inglis Washer Parts
- Does not dispense fabric softener or detergent
- Marks left on clothes
- Not cleaning dishes properly
- See more...
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair. Read more...
- Leaking
- Shaking and Moving
- Spinning Issues
- See more...
First I disconnected the washer from the water and power supply, then I laid it on its back.
The tub rested on the back of the washer, making two of the three suspension springs relax, and they were pretty easy to pull out with pliers. After the first two were out, I had to support the tub with a couple 2x4s to relax the third suspension spring.
Installation was the reverse of removal - install the lower suspension spring, remove the 2x4s, then install the two other suspension springs.
The tub balancing spring was easy to replace, and probably wasn't the cause of the problem.
With $25 in parts and about 15 minutes, my washer spins much more quietly. Read more...
- Shaking and Moving
- Spinning Issues
- Spins slowly
- See more...
- Does not dispense fabric softener or detergent
- Leaking
- Marks left on clothes
- See more...
One bolt held the entire agitator unit in the washer, as well as held the upper and lower halves together. Once that nut was removed the two halves seperated and the plastic clutch pieces could easily be replaced wtih the new onces in the repair kit.
Very easy do-it-yourself repair! Took about 20 minutes because I was being cautious. Next time I could do it in 5 minutes. Read more...
- Burning smell
- Leaking
- Noisy
- See more...
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
- Burning smell
- Noisy and Marks Left on Clothes
- Spinning Issues
- See more...
- Burning smell
- Spinning Issues
- Spins slowly
- See more...
- Burning smell
- Noisy and Marks Left on Clothes
- Spinning Issues
- See more...
- Shaking and Moving
- Spinning Issues
- See more...
- Leaking
- Leaks water
- Will not drain
- See more...
Inglis Washer Appliance Types
- Inglis Dishwasher Parts
- Inglis Dryer Parts
- Inglis Microwave Parts
- Inglis Parts
- Inglis Range Parts
- Inglis Refrigerator Parts
Related Inglis Washer Parts
- Inglis Washer Agitators
- Inglis Washer Transmissions and Clutches
- Inglis Washer Springs and Shock Absorbers
- Inglis Washer Hardware
- Inglis Washer Latchs
- Inglis Washer Seals and Gaskets
- Inglis Washer Hoses and Tubes
- Inglis Washer Switches
- Inglis Washer Dispensers
- Inglis Washer Caps and Lids
- Inglis Washer Knobs
- Inglis Washer Hinges
- Inglis Washer Brackets and Flanges
- Inglis Washer Circuit Boards and Touch Pads
- Inglis Washer Wire Plugs and Connectors
Popular Inglis Washer Models
Below are the most popular Inglis Washer models we have. Enter your model number in the search box to find your model.
- IFW7200TW10 Residential, Automatic
- IFW7300WW00 Residential, Automatic
- YIFW7300WW00
- ITW4300SQ0 Residential
- IFW7300WW01
- ITW4300SQ3 Residential
- IFW7300WW02
- IL45000 Residential
- IL42000 Residential
- IV45001 Residential
- ITW4600YQ0
- IS43000 Residential
- IK45000 Residential
- ITW4300XQ0
- IJ41001 Residential
- IJ43001 Residential
- IJ42001 Residential
- IS41000 Automatic
- IL44000 Residential
- IJ44001 Residential