ITW4300SQ0 Inglis Washer - Overview

Sections of the ITW4300SQ0

[Viewing 8 of 8]

Manuals & Care Guides for ITW4300SQ0

Click to download
Keep searches simple, eg. "belt" or "pump".
Agitator Directional Cogs – Part Number: 80040
Agitator Directional Cogs
★★★★★
★★★★★
(361)
PartSelect #: PS388034
Manufacturer #: 80040
This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your wa...
$4.39
  In Stock
Order within the next 12 hrs and your part ships today!
Direct Drive Motor Coupling – Part Number: 285753A
Direct Drive Motor Coupling
★★★★★
★★★★★
(160)
PartSelect #: PS1485646
Manufacturer #: 285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft....
$18.89
  In Stock
Order within the next 12 hrs and your part ships today!
Agitator Repair Kit – Part Number: 285811
Agitator Repair Kit
★★★★★
★★★★★
(203)
PartSelect #: PS334650
Manufacturer #: 285811
This kit (Medium Cam Agitator Repair Kit, Washer Agitator Cam Repair Kit, Cam Agitator) is used to repair the agitator. These parts are located inside the agitator auger near the top. You will need t...
$14.01
  In Stock
Order within the next 12 hrs and your part ships today!
Direct Drive Water Pump – Part Number: WP3363394
Direct Drive Water Pump
★★★★★
★★★★★
(102)
PartSelect #: PS11741239
Manufacturer #: WP3363394
The direct drive drain pump (Whirlpool Direct Drive Washer Pump, Drain Pump, Washer Drain Pump, Water Pump) removes water from the washer during the drain cycle without the use of a belt. The pump is ...
$48.71
  In Stock
Order within the next 12 hrs and your part ships today!
Suspension Spring – Part Number: WP63907
Suspension Spring
★★★★★
★★★★★
(27)
PartSelect #: PS11743345
Manufacturer #: WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could c...
$8.00
  In Stock
Order within the next 12 hrs and your part ships today!
Clutch Assembly – Part Number: 285785
Clutch Assembly
★★★★★
★★★★★
(79)
PartSelect #: PS334641
Manufacturer #: 285785
A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. If the clutch lining ...
$27.55
  In Stock
Order within the next 12 hrs and your part ships today!
Agitator Bolt – Part Number: WP358237
Agitator Bolt
★★★★★
★★★★★
(10)
PartSelect #: PS11741866
Manufacturer #: WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
$7.03
  In Stock
Order within the next 12 hrs and your part ships today!
Washer Lid Switch – Part Number: WP8318084
Washer Lid Switch
★★★★★
★★★★★
(77)
PartSelect #: PS11745957
Manufacturer #: WP8318084
This part is found in your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the green grounding wire. If your machine is ...
$45.93
  In Stock
Order within the next 12 hrs and your part ships today!
Thrust Spacer – Part Number: 285587
Thrust Spacer
★★★★★
★★★★★
(8)
PartSelect #: PS334562
Manufacturer #: 285587
This is a genuine OEM thrust spacer for your washer, and is also commonly known as a retainer ring. The spacer is about 2.5 inches in diameter, is made of plastic, and is white in color. It is used in...
$7.62
  In Stock
Order within the next 12 hrs and your part ships today!
Seal, Inner Cap – Part Number: WPW10072840
Seal, Inner Cap
★★★★★
★★★★★
(11)
PartSelect #: PS11748108
Manufacturer #: WPW10072840
This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollabl...
$11.09
  In Stock
Order within the next 12 hrs and your part ships today!
Agitator Cap Barrier with Seal – Part Number: WPW10074580
Agitator Cap Barrier with Seal
★★★★★
★★★★★
(11)
PartSelect #: PS11748113
Manufacturer #: WPW10074580
The O-Ring is included with this cap. It can be purchased separately as Part #WPW10072840.
$11.09
  In Stock
Order within the next 12 hrs and your part ships today!
Screw, 8/18 x 3/8 – Part Number: WP90767
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.41
  In Stock
Order within the next 12 hrs and your part ships today!

Questions And Answers for ITW4300SQ0

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

3 questions answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kristie
February 5, 2020
It seems to lose power. Would start back after thumping it. Now does not come on at all
For model number ITW4300SQ0
PartSelect logo
Hello and thank you for writing. It certainly sounds like it could be a faulty lid switch PS11745957 and/or a loose or a faulty capacitor PS11746660 you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Tony
March 3, 2020
How do you remove washer top to check or replace lid switch?
For model number ITW4300SQ0
PartSelect logo
Hello Tony, thank you for your question. There are two different versions of appliances that use that lid switch. The first set of instructions are as follows: Remove the two screws on the back of the control panel. The control panel then flips back. The switch is on the left side. To remove the switch, I first detached the wire to the control panel and unscrewed the grounding wire If the unit does not have the two screws at the back of the control panel follow these instructions: Before beginning any repair, please unplug the appliance from the electrical outlet or turn the circuit breaker off. First, pull the washer away from the wall to access the backside. Once removed from the wall you will need to loosen the Philips head screws holding the back panel in place. You will need to slide the top panel forward to release it from the mounting tabs. Rotate back the top panel which will expose the existing lid switch. Use a nut driver to remove the screw holding the ground wire in place. Lift up the top lid which will move an arm inside that connects to the switch by moving that arm it will allow you to remove the switch. Squeeze on the release tab to remove the switch and disconnect the wiring harness that goes to the lid switch. Reconnect the new switch to the wiring harness. Lift up the lid again and position the new switch and push it down so it clips into place. Lower the lid and connect the ground wire and screw it in place. With the switch installed, take the top panel and roll it back down into position and align the top panels mounting tabs then lock it into place. Use a Phillips head screw driver to tighten the remaining 2 screws into place. Reconnect the power cord or turn the circuit breaker back on and the washer should be ready to use. I hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Brenda
February 6, 2020
After spinning the tub is leaning toward the front of the washer. When it refills the water runs off the top rear of the tub and out the back side onto the floor. Do the suspension springs keep the drum level?
For model number ITW4300SQ0
PartSelect logo
Hello Brenda, thank you for your question. The suspension springs, and the balance ring, Part #: PS11741965, keep the tub level. I hope this helps.

Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the ITW4300SQ0

[Viewing 16 of 16]
Will not agitate
Fixed by
these parts
Fixing Fixing Fixing
Show All
Leaking
Fixed by
these parts
Fixing Fixing Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will not drain
Fixed by
these parts
Fixing Fixing Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing Fixing
Show All
Burning smell
Fixed by
these parts
Fixing Fixing Fixing
Show All
Spinning Issues
Fixed by
these parts
Fixing Fixing Fixing
Show All
Shaking and Moving
Fixed by
these parts
Fixing Fixing Fixing
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
Fixing Fixing Fixing
Show All
Leaks water
Fixed by
these parts
Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing Fixing Fixing
Show All
Not cleaning dishes properly
Fixed by
these parts
Fixing Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing
Show All
Noisy
Fixed by
these parts
Fixing
Show All
Touchpad does not respond
Fixed by
these parts
Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
Parts Used:
Direct Drive Motor Coupling
  • Jeff from Wayne, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
1099 of 1185 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer wouldn't agitate
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Parts Used:
Agitator Directional Cogs
  • mike from Kent, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
936 of 1022 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper portion of agitator, no longer pushing clothing down.
The instructions came with the repair kit, it was fairly simple and straight foward.

One bolt held the entire agitator unit in the washer, as well as held the upper and lower halves together. Once that nut was removed the two halves seperated and the plastic clutch pieces could easily be replaced wtih the new onces in the repair kit.

Very easy do-it-yourself repair! Took about 20 minutes because I was being cautious. Next time I could do it in 5 minutes.
Parts Used:
Agitator Repair Kit
  • Matt from Pawtucket, RI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Socket set
798 of 831 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!