General Electric Cooktop Elements and Burners
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular General Electric Cooktop Elements and Burners
General Electric Cooktop Haliant Element
PartSelect Number PS2321564
Manufacturer Part Number WB30T10130
This is a replacement haliant element for your cooktop or range. It is used with flat top ranges, and is found under the glass top of the range. This element is approximately 12 inches in diameter and is sold individually. The haliant surface element supplies the heat needed to the top of the cooktop. If your burner is not lighting up when it is turned on, you may have an issue with the haliant surface element. Be sure to disconnect power to the range before you begin this repair. To replace the element, remove the screws holding the cooktop in place, then remove it. Then, remove the screws holding the burner in place, disconnect the wires and replace the burner. Replace the cooktop and screw it back in to complete the repair.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Matt from Westr Grove, PA
Baking element and dual stovetop burner were fried
Baking element:First, turn off your breaker so you don't get injured. Using a small nut driver, remove the two screws that hold the element into the back of the oven. Once the screws are out, the element slides out, toward the oven opening. Be careful not to pull too hard, or the wires could disconnect from the back and be difficult to retrieve. Once the wires are exposed, disconnect them from the terminals. Attach them back to the new element, and put it back in. EASY For the stovetop, this is a glass top, so the burners are underneath. There are two small screws on the underside of the stove top, where the oven door closes. Remove those screws and then lift the front of the entire stove top. It will hinge at the back. There are two screws and little metal brackets that hold the burner in place. Remove those screws and brackets, disconnect the wires, and be sure to remember which wire goes where. Reattach the wires and screw the brackets back into the burner. Refasten the stovetop and you are good to go.
Read more...
General Electric Cooktop Radiant Element
PartSelect Number PS11729126
Manufacturer Part Number WB30X24111
This is a dual ceramic surface burner for ranges. This burner, also known as a heating element, is used within electric ranges to act as a stovetop burner. This burner measures approximately 10 inches in diameter and features a larger and smaller heating element that you can activate with the control board of your stovetop. If your stovetop burner is currently not heating correctly or consistently, then it will need to be replaced immediately. This burner features a ceramic construction with metal parts like the terminals that connect directly to your range. This burner is an OEM part and is sold individually, so depending on how many of this burner your range uses, you may need to consider that before ordering.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Brian from HAGERSTOWN, MD
Element out LF
Unplug stove.2 screws out ,lift top ,disconnect bad element, connect new element, put top down .2 screws in .plug stove back in...EASY PEASY
Read more...
General Electric Cooktop Dual Radiant Element
PartSelect Number PS2321567
Manufacturer Part Number WB30T10133
The dual radiant element for your range or cooktop provides the heat that you cook with. It is found under the main cooktop. If your element will not heat, you will need to replace it with this part. This radiant element is 9 inches in diameter and is the larger of the two element sizes on your range. Be sure to disconnect your range from the power source before completing this repair. This radiant element is sold individually.
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
Andrea from ORLANDO, FL
9" Radiant Element did not heat up.
I started by Unscrewing the range top. 2 small screws. I took off the old piece by unclipping the piece . Then I color coded each wire so that I would know exactly where I would place the wires for the new part. 30 min maximum time spent changing the part. Please don't forget to unplug the range before you start.
Read more...
General Electric Cooktop Range Cap
PartSelect Number PS954107
Manufacturer Part Number WB28K10222
This is a replacement burner cap for your gas range or cooktop. The burner cap is found on the burner head, and prevents debris from getting into the head when it is not in use. The cap is black in color and is sold individually. It is a little more than 4 inches in diameter. To replace the burner cap, simply remove the damaged cap, and replace it with the new one. No tools are required for this repair. This is an OEM part from the manufacturer.
Installation Instructions
Alejandro from Newark, NJ
The Burners and Burner Caps were missing
Very simple repair. I bought the Range without the Burners and Burner Caps. So all I had to do was to purchase the Burners and the Burner Caps and drop them in. Wish everything in life would be that simple.
Read more...
General Electric Cooktop Range Burner Cap Black Medium 9500 Btu
PartSelect Number PS954202
Manufacturer Part Number WB29K10023
This burner cap is for your gas range, and acts as a cover for the burner head. It is black in color and just over 3 inches in diameter. If your old burner cap is damaged or missing, this is the part that will replace it. This is an OEM part sourced directly from the manufacturer and is sold individually.
Installation Instructions
John from Simi Valley, CA
Missing burner head and all 4 caps on cook top.
All I needed to do was replace the missing burner head and caps. Cook top is now back in service. Thanks for getting me the parts in a very timely manor!
Read more...
General Electric Cooktop Range Radiant Element 8
PartSelect Number PS2321566
Manufacturer Part Number WB30T10132
This radiant stovetop element, or burner, is a genuine replacement part, and is 8 inches in diameter. The radiant element heats your cookware as you prepare food on the stovetop. To complete this repair, you will need a screwdriver to remove the screws holding the cooktop in place. Lift the cooktop up, and remove the screw and clip holding the old burner in place. Replace with the new element.
Fixes these symptoms
- Element will not heat
- Will Not Start
- See more...
Installation Instructions
Vilas from HANOVER TWP, PA
Back burner was not working.
Took top of stove off, disconnected the heating element, re-installed the new element and now my stove works fine.
Read more...
General Electric Cooktop Range Burner Cap
PartSelect Number PS954203
Manufacturer Part Number WB29K10024
This is a burner cap for your gas range. The cap acts as a cover for the burner head. If your old burner cap is damaged or missing, this is the part that will replace it. The cap is black in color and about 3 and a half inches in diameter. This is a quality OEM part sourced directly from the manufacturer. This cap is sold individually.
Installation Instructions
John from Simi Valley, CA
Missing burner head and all 4 caps on cook top.
All I needed to do was replace the missing burner head and caps. Cook top is now back in service. Thanks for getting me the parts in a very timely manor!
Read more...
Your Price
$55.39
In Stock
General Electric Cooktop Range Surface Element 8 2350w
PartSelect Number PS243868
Manufacturer Part Number WB30M2
The surface element, also known as the coil surface element, transfers heat to the area on top of range. The element is 8 inches in diameter. If your surface element does not heat, over heats, or heats inconsistently, replacing this part can be the solution to your issue. To determine whether the element is defective, use a multimeter to test it. Before installing the new element, make sure the drip bowl is properly aligned with the notch of the pan. Insert the new element into the reciprocal at a 40 degree angle. Refer to the instructions provided by the manufacturer for more guidance.
Fixes these symptoms
- Element will not heat
- Little to no heat when broiling
- See more...
Installation Instructions
John from San Ramon, CA
I needed new surface elements & burner bowls
This was about the simplest fix I've ever done. Just pulled off the old surface elements & burner bowls, wiped down the range top, and put in the new parts. Perfect fit. No problems at all. $$ well spent. ParsSelect shipped quickly, and they arrived well packaged. A+ experience all around. Thanks PartSelect. JA, San Ramon, CA
Read more...
Your Price
$48.95
In Stock
General Electric Cooktop Range Surface Element
PartSelect Number PS243867
Manufacturer Part Number WB30M1
If you notice that your surface element will not heat properly, you may need to replace it. This surface element is 6 inches in diameter and 240V. It is a Y-frame surface burner element with five turns and a metallic center medallion. When completing this repair, if you notice any signs of corrosion or overheating on the terminal, you may want to consider replacing the terminal block as well as the surface element. Many of our customers have rated this repair as easy. To complete this repair, simply tilt the old element up and remove it, and then replace it with your new one.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
John from San Ramon, CA
I needed new surface elements & burner bowls
This was about the simplest fix I've ever done. Just pulled off the old surface elements & burner bowls, wiped down the range top, and put in the new parts. Perfect fit. No problems at all. $$ well spent. ParsSelect shipped quickly, and they arrived well packaged. A+ experience all around. Thanks PartSelect. JA, San Ramon, CA
Read more...
General Electric Cooktop Haliant Element
PartSelect Number PS2339867
Manufacturer Part Number WB30T10136
This surface element is designed to supply heat to a designated cooking area on the top of an electric range, enabling efficient and consistent heating for everyday meal preparation. Positioned beneath the cooktop surface, it plays a key role in maintaining proper temperature control. Before installing, be sure to unplug the range or switch off the corresponding circuit breaker to ensure safety. Wearing protective work gloves is also recommended to prevent injury while handling electrical components.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Marco Antonio from CORP CHRISTI, TX
Element broket
1.- going online to orden part 2 disconnect the power from the aplaince shoot Dow the power 3 tear down the appliance and disconnect the four terminals from the damage part reconnect the terminals to th new part reensamble the appliance and ready to go save $275 bucks in handy man labor
Read more...
Related General Electric Cooktop Parts
- All General Electric Cooktop parts
- General Electric Cooktop Brackets and Flanges
- General Electric Cooktop Caps and Lids
- General Electric Cooktop Circuit Boards and Touch Pads
- General Electric Cooktop Cooktops
- General Electric Cooktop Doors
- General Electric Cooktop Drawers and Glides
- General Electric Cooktop Drip Bowls
- General Electric Cooktop Fans and Blowers
- General Electric Cooktop Fuses
- General Electric Cooktop Grates
- General Electric Cooktop Hardware
- General Electric Cooktop Igniters
- General Electric Cooktop Ignitions
- General Electric Cooktop Insulations
- General Electric Cooktop Knobs
- General Electric Cooktop Lights and Bulbs
- General Electric Cooktop Manuals and Literatures
- General Electric Cooktop Panels
- General Electric Cooktop Power Cords
- General Electric Cooktop Seals and Gaskets
- General Electric Cooktop Springs and Shock Absorbers
- General Electric Cooktop Switches
- General Electric Cooktop Trims
- General Electric Cooktop Valves
- General Electric Cooktop Wire Plugs and Connectors