WTW6300SW2 Whirlpool Washer - Instructions

I mounted the left and right hinge assemblys into the washer (spring assembly) and then mounted the glass top on to the hinge assemblies. Inserted the screws and tightened as required.

I pulled out the old cap with my hands and jammed the new thingy into place. The lady of house did the repair. Easy

lifted top using putty knife to push back holding clips.secured top so it did not fall. moved basket to one corner and lifted the spring up, while it was lifted remove the plastic holding rings. Then push down on holding clips that are near bottom of side of basket and the suspension rod just eases out. do that for all 4 and you are done.

fairly simple remove and put back in …I watched a video of a similar Maytag pump replace got some tips…the electoral connection is shielded by a pull up tab…so it was quite simple I got extra hose clamps in case?…didn’t need them

Removed the softener dispenser and cap that's under it. Used 7/17" socket with an 18" long extension to reach the bolt that holds agitator down. Pulled auger off, pulled lower agitator off. Removed the 6 philips head screws that hold basket hub in place. Removed hub and installed new one, replaced screws. Lightly greased spline and reinstalled lower agitator. The auger has the cam section in it. A trick to get the rollers in place is to secure them to the cam with rubber band. Have string tied to the band. Insert the cam and when almose all the way in, pull rubber band off and the rollers stay in place. Reinstalled the bolt, cap and softener dispenser.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I just unscrewed the top agitator cap and slid the o-ring on and put it back. Done in seconds.

shook bottle and painted waited a day and repeated

Just had to remove cap on agitator and replace new rubber seal.

Well i watched a video on youtube that demonstrated the repair, and it seemed easy enough, so i ordered the parts which arrived quickly enough that we avoided a trip to the laundry mat, very cool! So i did just what they said to do, unplug machine, tape down the lid, use a putty knife to pop the retaining springs in front. I used a long screwdriver to hold up rod on top and then rotate the ball around and let the rod fall through, them i used a yard stick to pop out cup on bottom. I did have assistance holding the drum back so i could see, Then i reversed the process with a new rod. The only reason it took 30 min was i did not put the cups under the balls on top, because it didnt have them in the first place, i decided to put them in after then reading the instructions. The machine runs like new, and my wife is very happy!!

The rod kit fixed the issue. I cant really explain how I did it, because I dint know if I did it the right way.

removed glass cover control panel & top of machine to replace hinge spring.

It was not easy but I dit my sell

The instructions displayed the parts location and and some instruction. The top of the unit will release and pivot up after the two catches at the front are presed in at the front seam. The catches are located about 6 inches in from the sides. Before lifting the top though you should secure the lid to the top. I used some masking tape. Pivot the top up and brace the top to prevent it from falling back too far or forward over your work access. I leaned the top back against the wall behind the washer. Once the top was secure I began by lifting one conner of the tub assembly so that a corner dampner assembly could be removed. The top of the dampener assembly has a loop which grabes the plastic cup at the top frame of the washer. Lift the tub assembly (about 30lbs) on one corner and as the hook becomes free rotate the plastic cup to disengage the hook from the cup. To make it easier to work inside the washer frame I used the bar clamp to hold the tub asembly to one side so that I could reach along the damper assembly to pop loose the top retainer at the tub by pushing down with a screwdriver. Once the dampener assembly was loose it can be removed and the new one inserted in its place. I repeated these steps for each dampener and was done in about 30 minutes. You may want to note there is a wire clip on the right rear dampener and this was easily removed and reinstalled on the new assembly.

went well but alas the problem still exists.