Back
Back
Keep typing for more specific results...
Models > WDT970SAHV0 > Instructions

WDT970SAHV0 Whirlpool Dishwasher - Instructions

All Instructions for the WDT970SAHV0
61 - 75 of 544
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher was leaking but I couldn't determine exact cause, so I tried replacing the gasket which is common cause of leaks.
Removed old gasket, cleaned track thoroughly, then followed instructions from video on Part Select order form. Instructions very clear and precise. Getting the new gasket was a little tedious at the corners but take your time and work the gasket with your fingers as shown on the video.
Parts Used:
Dishwasher Door Seal
  • Dale from DOWNINGTOWN, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced the rack adjuster left and right side
I looked up the repair on youtube and followed along step by step.
I am a 64 year old female and the job was easier to do while watching a repairman than it would have been to read instructions.
The internet is great for some things!
Parts Used:
Dishwasher Upper Dishrack
  • ELIZABETH from CINCINNATI, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The wheels on the upper rack kept coming off
What I needed were simple clips to lock in the wheels. I ended up getting a kit that required replacement of the roller tracts on both sides of the upper rack. The instructions were terrible. The repair took far more time than it should have. Once one side was fixed it was easy to fix the other side. By then I had worked my way around the muddled instructions.
Parts Used:
Dishwasher Positioner Upper Rack Adjuster Kit
  • Robert from THE WOODLANDS, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
12 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not drain
After bailing out the unit, filled filter hole with a moderate amount of Dawn dish washing detergent. Ran dishwasher twice to remove all Dawn from the unit. Had to bailout the water (and suds) from the washer both times. After the dishwasher finally drained I inserted the new filter..
Parts Used:
Dishwasher Filter
  • Edward F from CINCINNATI, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain hose leaking
I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.
Parts Used:
Dishwasher Drain Hose
  • Robert from Beaufort, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
8 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door spring link broke.
Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.
Parts Used:
Dishwasher Door Balance Link Kit
  • Martin from Discovery Bay, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door gasket leaked water at the bottom of the door, No visible gasket damage.
I removed and reinstalled the new gasket per the video instructions, but I found the corners to be much harder to install than indicated. I finally used a large, flat, dull screwdriver to carefully push the gasket all the way in, and used my fingers to feel whether the gasket was all the way in. I figured if the gasket wasn't all the way in, I would have a leak at the bottom of the door because the top of the gasket would stick out farther than the bottom, which is exactly what the original symptoms were. Perhaps I didn't need a new gasket? There was no visible damage. Pushing in the corners of the original gasket may have fixed it, but the new gasket worked perfectly! Thanks, Part Select!!
Parts Used:
Dishwasher Door Seal
  • WILLIAM from SYRACUSE, IN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not latch shut
Following a utube video made it easy. Removed the outer cover of the door to expose latch. Two screws remove the latch, pay attention to how it was positioned and put the new one on and then replace the panel. But first turn off the electricity to the unit at the fuse box.
Parts Used:
Black Door Latch
  • RONALD from PRESCOTT, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I damaged the grommet when removing the recirc pump
repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet
Parts Used:
Dishwasher Grommet
  • john from SANFORD, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The wheels broke off from the rack hangers.
The replacement kit came with no instructions in the box, so I found the instructional video online. This video pointed me in the right direction so I could take it the rest of the way myself.

Here is the link to the instructional video i used
https://www.partselect.com/PS10065979-Whirlpool-W10712395-Upper-Rack-Adjuster-Kit-White-Wheels-Left-and-Right-Sides.htm

Even though I purchased the end cap pieces for the roller stops, I was able to reuse the original pieces so these are to be keep for spare if required.

This was a very cost effective repair instead of replacing the entire rack assembly.

NOTE: The original Wheel bracket was a molded plastic piece, but the replacement is Stainless Steel. This had no impact on the functionality, but did add a small amount of noise during the wash cycle. My belief is this is the water hitting the steel vs. hitting the plastic.
Parts Used:
Dishwasher Rack Track Stop Upper Rack Adjuster Kit
  • Richard from PHELAN, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
9 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top rack wheel broken causing rack to fall when extended too far.
watched instructions and proceeded. Parts were self evident after watch ing video. Easy replacement.
Parts Used:
Dishwasher Rack Track Stop Upper Rack Adjuster Kit
  • Robert from LITTLETON, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking through the sump shaft seal
First I removed everything off of the bottom of the dishwasher. Then I removed the main center piece that everything mounts to. Then I reinstalled the new center piece with the help of some evoo cooking spray (extra virgin olive oil) I sprayed it on the rubber seal to aid in getting that center piece installed without a battle. Then I reinstalled everything else in the reverse order that I removed it. The evoo cooking spray works wonders for more than just cooking !!!
Parts Used:
Sump
  • Jason from MOLINE, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One of the old stops broke
Snapped the new stops on. It took about 2 minutes.
Parts Used:
Dishwasher Rack Track Stop
  • Dwight from KENT, WA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old hose possible leakage
put new hose on, very easy.
Parts Used:
Dishwasher Drain Hose
  • Fred from Kernersville, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
8 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the tines in the upper basket of the dishwasher were falling apart
Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.
Parts Used:
Dishwasher Tine Row Kit Of 2
  • Dorothy from BILLINGS, MT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WDT970SAHV0
61 - 75 of 544