SVE87600B Jenn-Air Range - Instructions

I only had to unscrew two screws to remove the existing element. Unfortunately, when I removed the element I found that the electrical wire connected to it had melted off, so the element is actually still good. I had to strip the wire back and put a new wire connector on. Once that was done I hooked the element back on and screwed it back together.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

Simply unscrewed two screws holding the old element and replaced it with the new one. Note, of course I had to disconnect the wires that plugged into the back. Really easy and quick, less than $50 total for an that would cost over $2200 today.

took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

Make sure you turn breaker off install both wires and screw the bracket into the back of the oven. You could use a phillips screw driver but with my ovens age seemed like it wanted to strip it out so I used a socket instead. Turn on the breaker and it works like new

Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it easily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done

My husband did the repair. He had difficulty removing the old element, probably because it had been in there for 20 years. Once he got the old element out, it took less than 30 minutes to install the new one.

Remove Vent Cover, Remove Old Filter, Replace With New Filter, Replace Vent Cover, Repair Complete

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

Turn off the electrical breaker before starting! Open the oven door & remove the 4 silver hex head screws under the bottom of the control panel with a 1/4 " nut driver. Pull out on the bottom of panel. This will access the clock assembly. Unplug the ribbon cable by pushing in & up on the small clips on each end of the connector - this is a little tricky but not that difficult. Remove the two small connectors and remove the two clock assembly mounting screws. Reverse the procedure for installation. This corrected the problem with the broil element not working - apparently the electronic clock assembly was the problem there as well.

There were only 4 screws to remove to take off the thingy that houses the electronics portion. Then, there was a ribbon connector and two push on connectors to unconnect. Unscrewed the 4 nuts holding the faulty Assembly in place, replaced with new Assembly, and reversed the process.

That easy. The only problem was making sure which of the parts we actually needed.

I took the broiler pan out of the shipping container and put it in the oven.

it took me longer to get my portable screwdriver from my shop than to remove four screws from the panel and two screws from the clock assembly and to unplug and replug wiring , then reassemble the panel