Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
This suspension rod kit is a genuine OEM replacement kit that is compatible with various models of washing machine. The kit is responsible for supporting the inner tub of the washing machine and absor...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This is a shift actuator, and is designed for use in washing machines. This shift actuator is made to change the mode of the motor between spin and agitate, as well as communicate with the control boa...
This agitator assembly is an authentic OEM part that is compatible with various models of washing machines. It consists of a central shaft with a series of fins attached to it. When the washer is oper...
Introducing the Whirlpool Washer Washplate Screw - your reliable solution for fixing broken or loose washplates in your washing machine. This OEM genuine part, compatible with distinct models of Whirl...
This is an impact absorber, also known as a sound dampening pad, for washing machines. This sound dampening pad attaches to the top of your washing machine drum to reduce the severity and harshness of...
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
$26.17
In Stock
Questions And Answers for MVW4505MW2
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jim
November 21, 2024
Does it have a lint filter that is cleanable.
For model number MVW4505MW2
Hello Jim, Thank you for writing. There is a filter in the bottom of the Outer Drum, PartSelect #: PS16660526. Normally it is self cleaning but over time it can get a build up. We hope this helps!
Push on, starts to sense for 7 seconds, lid does not lock and then done light comes on. I unplug power for min. and try again , sometimes lid locks but after few seconds it goes to done. Water valves never activate . I suspect a power spike during a recent thunderstorm while i was not home, maybe. Washer is 6 mo. Old
For model number MVW4505MW2
Hi Mike, thank you for reaching out. We would suggest checking the lid lock first. If it is fine, the issue could be with the control board, part number PS17917531. It acts as the brain of the appliance, managing various functions and ensuring optimal performance of the washing machine. You may need to replace it to fix the issue. We hope this solves your problem!
Washer starts to sensor and sometimes starts to add water and then all lights flash and goes to done. I unplug and wait 5 min and try again and each time i try to to restart it , it does someting a little different each time. But it will eventually flash the light for each cycle and goes done but sometimes it will not unlock lid aftet showing done.. tried several times by unplugging power for several minutes and retry
For model number MVW4505MW2
Hi Mike, thank you for the question. Check the lid lock for any fault first. If it is fine, the issue could be with the control board, part number PS17917531. It serves as the brain of a washing machine, managing various functions and ensuring optimal performance. You may need to replace it to fix the issue. We hope this solves your problem!
New washing machine making a grinding noise, what could be causing this?
For model number MVW4505MW2
Hello Kimberly, thank you for contacting us. A grinding noise in the washer could most probably occur due to a malfunctioning transmission. We would recommend checking the transmission, part number PS16730207, to solve the problem. We hope this helps!
Dryer doesn't put out enough heat to dry the clothes
For model number MVW4505MW2
Hello Susan, thank you for your inquiry. A clogged or kinked venting system can reduce airflow and heat output. Inspect the venting system to ensure it's clear and not blocked. If that is not the cause, we would recommend checking the thermistor, part number PS11746740, to solve the problem. A malfunctioning thermistor can most probably cause this problem. We hope this helps!
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Watched a video to get a general idea. Moved washer to garage. Raised lid, supported with s-hook and light chain. Front springs were easy, except no hole for the rod to hang in so used chain and small screwdriver through mounting hole. Back springs were not as easy. Finally removed the back panel to get to the rods. Bingo, much easier an
... Read mored only took 5 min to remove the back panel. reassemble and she works like a charm. Suggest to find a video reflecting your particular brand and model as all are similar but uniquely different. Easy project though.
