MED6600TQ0 Maytag Dryer - Instructions

The only challenging part was getting the old catch out. It can easily fall inside the door, not that this is really a problem, just leave it there. Using pliers get a good grip on the edge of the old catch and rock the top out, then pull to get the bottom out. There will now be an open hole. Align the new part with the open hole, and simply push it in. It will catch, and click into place. No tools are needed to install.

I removed the broken door catch with a screw driver. I then used a pair of pliers to push the new door catch in place. It was an easy repair and saved me quite a bit of money.

Pulled back off dryer as in video and followed directions. One part in the kit was not necessary. Just replaced the fuse and put it all together again and Voila! Dryer works again.

This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.

Drum belt broke. Found drive shaft belt guide broke. Replaced pulley wheel since I had it apart.

Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.

removed the back housing of the dryer and located the thermal switch. unscrewed the old one, popped in the new one and whala! I was back in business!

put the back cover back on the dryer and pushed it back into place.

first i removed the back cover by removing the six 1/4 inch screws then i removed the wires to the thermal switch there were three of them and using an ohm meter i checked each one for continuity until i found the one that had an open circuit. i removed the two 1/4 inch screws holding it in place and replaced it with the new one.

I first unplugged the dryer and pulled it away from the wall. I had to remove the vent tubing to gain access to the rear of the unit, then removed the screws on the back panel of the dryer. I took off the panel and noticed that lint that had gathered over the years around the back of the dryer. I vacuumed it clean then proceeded to problem solve. I noticed four easily identifiable areas, the thermal cut-off switch and thermostat located by the heating coil and the thermostat and fuse near the venting area. I first checked the fuse with a ohm meter, it was okay. I removed each component one at a time and created a bypass with a alligator clip wire. Plugged the dryer back in to determine if heat was produced while testing each area one at a time. I determined that heat was produced after bypassing the thermal cut-off switch. I then ordered the thermal cut-off switch kit (arrived within 3 days) and installed it within 20 minutes. The longest time spent was trouble shooting, the removal and installation was very easy. By the way, I did use the ohm meter to check the resistance across the thermostats as indicated in previous postings, but I found the results and technique to be more confusing. A bypass worked the best for me and much more reliable. The heat started immediately. I highly recommend downloading the schematics of your unit for part number and location identification.

I shorted the thermal cutout after removing the back.
I then ordered the thermal Cut-Off Kit from PartSelect.
While this was not my first order from them, I was still impressed with the ease and by how soon I received the part without any hassles or glitches. PartSelect will be my primary parts supplier from now on.

I bought a new thermo cut off and replaced the old one.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Didn't have a putty knife, so used a flathead screwdriver to carefully pop out the top, then bottom of the catch. New one easily popped in. Took less than one minute!

pushed the broken catch into the door and snapped the new one back in. Works perfectly!