LSDF9969BD LG Dishwasher - Instructions

Removed two screws (one each side) and the toe kick plate at the bottom. Slide the dishwasher out from the cabinets about 10", remove broken cord clip from door and spring. Install door clip and wrap cord around pulley , attach to spring then attach spring to door, lifting the door will help attach the spring. Do one side of the door at a time.

Cables have broken about every 3-6 months after original ones broke after 8 years. Removed front kick plate screws and remove kick plate, and remove two top screws holding Dishwasher to counter-top. Pull dishwasher out about 10 inches. Remove all broken parts and replace cables. Side dishwasher back in place and reinstall removed screws. I just hope these Cables last longer than the ones I had bought from another source. I have replaced those Cables 5 times already and hope these last MUCH longer. Delivery was very fast from PartSelect.

The parts are wrong and am trying to return them. There was no return information included with delivery. Calling the Customer Service number for assistance did not work.

I would just like to return these rollers and would like a return address.

Thank you!
Penelope

I went to Youtube to get an idea of how to approach the repair. First turn off the electric power to the dishwasher. Then turn off the water valve that's connected to the dishwasher. Then disconnect both electrical and water lines connected to the dishwasher. Then remove the dishwasher from under the counter. Then place the dishwaher upside down. Remove the old hose,and install the new hose. Place the dishwasher right side up, and reconnect the water line, and electric line. Place the dishwasher back in place, and you're done.

Saw a YouTube video that explained the problem was the pump. Removed dishwasher from under the counter, flipped it on its side, and unplugged the unit. Removed bottom cover and the pump is right there. Used pliers to lose and move 3 hose clamps. Unplugged 3 wires and unscrewed the ground. Unhooked rubber hold downs and removed. Installed new pump. Parts Select pricing was best I found and shipping was fast. Nice to have a quiet house again when running the dishwasher. Cost in total was less than $100.

I ordered four wheels to replace the two that were broken and to have two as spares. The wheels are to be snapped onto the bottom of the lower basket. The new wheels broke upon being installed. My extra wheels came in handy. I put them in very hot water for a few minutes to soften the plastic. I put a little Vaseline on the post they were to be attached to. The wheels then slid on and snapped correctly.

Crazy as it seems, the bottom spray bar was spraying water down thus pushing more water under the door. The spray bar top half separated from the bottom half and the gap was spray water down instead of through all holes like designed. Do this before repairing anything!!!

I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.

These were a simple snap on item. It took longer to carry the parts from the porch that to install. Recently purchased house. Rollers were missing due to overload?? Removed the remaining roller pieces. Cleaned and straightened the axle shafts, spray lubed the tray and snapped the new pieces in place.

Pried old rollers with screwdriver. pushed (or 'pliered' new rollers, after straightening gudie pins, if necessary. One new roller broke a minute after installation, but I ordered extras because 6 odl rollers had alread broken), so we're OK for another year or so...

The connector assembly connects to a spring to hold the door from falling down. You need to disconnect the power cord, the water line and the drain hose before you move the dishwasher out the kitchen counter. There are several screws that hols the dishwasher in place top, side and bottom. Removed all screws then pull the dishwasher out very slow. Take the side panel by un-screwing all the screws around the panel in my case where five screws (two in the front so you have to open the door to get to them). You need to keep the door down to connect the assembly to the door bracket and the go through the pulley then to the spring, very easy. Put the side panel back and push the dishwasher in place use the same screws and reconnect the hose the water line and the power and you are done.

went online with model number, looked up appliance exploded view on your site and ordered parts. parts came the next day. second time we have ordered from you. you rock!

pulled the dishwasher out, removed the side panel. It was very easy to replace the connector once the dishwasher was out and the side panel was removed. There are about five screws to remove the side panel. I replaced the unbroken connector on the other side since I had the dishwasher out.

Undo screws holding dishwasher in place, two screw just inside door one each side, should be covered with plastic cap. Slide dishwasher out, there is a spring on each side of the door connected through the connector to the door and cabinet. Slide connector our, install new one, slide disher back in, reattach screws holding dishwasher in place and your done.