LDF6810ST ((01)(ASTEEUS)) LG Dishwasher - Instructions

Took off the broken one and snap on the new one.

Loosened 3 screws and unhooked supply line and electric box and pulled it out.

I got on line and 'chatted' with an online person. After describing the problem, she told me it had to be the water entry pump. I ordered it and put it in. VERY EASY. Then, it still didn't want to work right. It would start & stop and never get a full cycle. So I got online and looked at the diagrams provided, and decided to take off the "Filter Assembly Mesh". After already replacing the water entry pump, I took off the Filter Asssembly Mesh part (by undoing 8 screws), & found that the pump gasket was somewhat coming apart. Upon waiting for receipt of these two items, I realized that I thought it wasn't getting hot either. Once again, I looked at the provided online diagrams and ordered the heater assembly. After placing the dishwasher on its front again, I traced the connecting wires, marked them for later replacement & removed those & removed the ground wire and pulled out the old heater. Voila', its was rusted in two places. Ordered the heater. Upon receipt, I placed a small amount of Vaseline around the heater gasket prior to inserting fully. Reversed the process, assured myself everything was in and properly seated and tightened. Put the machine back in and it works great!

pulled dishwasher out of cabinet, removed side panel held by screws front and back, removed broken tension rope installed new rope, replaced side panel pushed dishwasher back into cabinet and fastened
to countertop, door works like new now, (the chief cook is happy as she can be)

The repair took right at one hour. Repair length of time will depend on what all you have to disconnect to get your dish washer out so you can remove both side panels where you will be able to access the door springs, etc. There is a door spring on each side and I recommend replacing both connectors cords while you have the dishwasher out. Mine were both broken. One thing I noticed when doing my repair was that the bracket that is on the bottom of the door was not aligned properly to the small pulley that the connector cords travels under. If yours is out of alignment you will be able to tell once you get the connector cord installed. I used heavy pliers to bend the bracket slightly inward so the connector cords rides in the center of the pulley and not off to the outside as before. This may be why mine broke in the first place. After part replacement, reinstall the door panels and put the washer back in service. There are also YouTube's of this repair so you can see what you are getting into. Basic repair.

Replaced it . Simple

Removed two screws (one each side) and the toe kick plate at the bottom. Slide the dishwasher out from the cabinets about 10", remove broken cord clip from door and spring. Install door clip and wrap cord around pulley , attach to spring then attach spring to door, lifting the door will help attach the spring. Do one side of the door at a time.

snapped on new axel-wheel assembly

Cables have broken about every 3-6 months after original ones broke after 8 years. Removed front kick plate screws and remove kick plate, and remove two top screws holding Dishwasher to counter-top. Pull dishwasher out about 10 inches. Remove all broken parts and replace cables. Side dishwasher back in place and reinstall removed screws. I just hope these Cables last longer than the ones I had bought from another source. I have replaced those Cables 5 times already and hope these last MUCH longer. Delivery was very fast from PartSelect.

All I needed was the rinse aid cap, damm shame one must pay $75 for for the complete rinse aid dispenser just to replace the cap. I will not purchase LG product again. The cost to just replace the cap is a rip-off.

I watched the video and it showed every step to remove the old part and replace the new one. Went fairly easy except when put the new motor in the new seal was difficult to put on. I think if I would taken off the front door I could have got close to the back of the rubber seal to secure it a little easier. Had to use a rubber hammer hold my breath to not brake the plastic motor. But that was only way I could get in. The video showed it going rely easy that was not the case because it was a new seal. In the end it all worked out.
Thanks for the video's to help

Very easy repair. First remove all the screws from the inside of the door, making sure you support the outside part of the door with a pot under it on the floor. Pull the locker part out, remove wire connection with needlenose pliers, and install replacement part. Put door back together, and you're done.

Saw a YouTube video that explained the problem was the pump. Removed dishwasher from under the counter, flipped it on its side, and unplugged the unit. Removed bottom cover and the pump is right there. Used pliers to lose and move 3 hose clamps. Unplugged 3 wires and unscrewed the ground. Unhooked rubber hold downs and removed. Installed new pump. Parts Select pricing was best I found and shipping was fast. Nice to have a quiet house again when running the dishwasher. Cost in total was less than $100.

connector was broken. just attached new connector to spring on each side of door. easy fix.

The parts are wrong and am trying to return them. There was no return information included with delivery. Calling the Customer Service number for assistance did not work.

I would just like to return these rollers and would like a return address.

Thank you!
Penelope