JDRP548WP02 Jenn-Air Range - Instructions

Removed old terminal block & replaced with new one. Very simple. Did NOT have to replace cover as stated you should. Shipping could have been a little faster. Will definetly try this site again.

It was a matter of swapping out the old door with new door. In all, it was a snap . Around 10 screws to take it apart and a few brackets to hold it all together.

Disconnect power and turn off gas. Remove all grills, knobs and burners. Under the burners are 2 Phillips head screws. Remove all 10 screws. Remove surface plate. Remove the one igniter with problem. There is a small metal clip holding it in place. Remove the wire. Install new ignitor and reverse all steps above.

I found that what was keeping the old temp sensor electrical connection attached to the stove-side connection was a little tab. It wasn't obvious that that was the thing that was keeping the connection secure but there weren't any other alternatives. So pushing the tab up with the metal probe (just a narrow rigid metal wire) allowed me to pull the connection apart.

All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.

Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.

Order part from this site was very easy. It matched perfectly and I had no problem installing it

Quickly

With just the removal of a few screws I was able to replace the glass with the side benefit of cleaning the outter glass that had gotten dirty over the years with use. This is a simple project that all can complete.

Removed the door from the oven. Undid all the parts above the inner glass door. Installed the inner glass and reassembled the door. Reinstalled oven door.

After reading all the other entries, I decided that I could do this! My first hurdle was getting the oven door off the hinges. Mine were not like any of the others described. My son-in-law looked at them and couldn't figure them out. So, I found the original installation instructions and, lo and behold, they said to flip the lever (one finger operation) in each of the rectangular holes holding the door onto the oven and then lift up until the door comes off. I did it, and it did! Boy, is it heavy! From there I just followed everyone else's instruction about undoing the screws, washing the glass panels, lining up the screw holes to get it back together, etc. One thing that took me longer was that the steel panel needs to go back the way it came out, not flipped! When I washed the glass panel it held, I put it down wrong and then "installed" it backwards. Luckily, I have a double oven and looked at the other one to see what was holding up the re-assembly! I'm glad that one of the others mentioned that the glass on the "bottom", the one that broke, isn't held in my screws or steel plates -- nothing, so I wasn't surprised when I got to it and it was "floating" on the insulation. My white insulation was like a fine fiberglass and was easy to stuff back in around the rim of the new glass. Took me a little over one hour. So, no more wet rags on hot glass (you'd think after living 72 years that I would remember this!) The glass fit perfectly and my husband would have been proud of me -- that I tackled a job that he usually handled, and that I saved over $200 for a couple of hours of labor and travel time.

Opened overn door and inserted allen wrenchs through the holes in the door hinges. Close the door until it makes contact with the allen wrenchs, then grasp the oven door handle and the bottom of the oven door and lift up to remove the door. Place the door on a flat surface,(I used a bed) and remove the screws to gain access to the glass. Upon re-assesbly, leave door flat line up and re-install all screws before putting the front pannel back on. Insert door back into the oven and open, remove the allen wrenches and close the door. The process is easy and will take 30 minutes to an hour and save you a $100.00 service call!

Switched spark module from one of the other burners to see if it would work and it did (presto)process of elimination and being in the propane business for 32 years helped

removed unit from cabinet tested switch it was OK checked wiring and found shorted out wire leading to switch. cut out bad section and spliced wire back together
problem solved

Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.

Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on

unscrewed the oven door, took off the entire door, pulled apart the glass pieces and replaced