JDB1105AWW10 Jenn-Air Dishwasher - Instructions

After noticing that the nozzles in the washer arms seemed clogged, I ordered replacements from PartSelect.com. Installing them was a breeze. The upper arm had a torx screw in it and the bottom just required a nut driver to get off. I replaced the arms and ran some DishWasher Magic through it and now my dishes are clean again!

Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.

The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.

Unfortunately, my experience was unlike that of the other people who posted. While everything did go back together it was very difficult to get it all to press down tightly enough to tighten each set of screws. The project took about 2.5 hrs and I still don't think it is exactly right. I'm still going to have a professional out to finish the job. Also, the tool needed to complete the job was nothing fancy, but also not in everyone's home tool kit.

1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.

I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

I used a flat screwdriver and small forceps pliers to remove the broken wheel on the lower rack, followed the online video and it was done in a few moments. On the upper one I removed the end piece using small forceps pliers then removed the broken wheel. I used the flat screwdriver to ease the new wheel assembly on the the rack, engaged it in the track then replaced the end piece on the track and the repair was complete. I did order 2 of each item to keep as spare for the next repair!

It is such an easy snap-on repair that a child could do it. I am grateful that your company had a picture so I could compare my broken part with the ones you guys have as I couldn't find my model number. I took my time to do the job right, so it took me almost 15 seconds! lol

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

Easy to repair and saved us replacing a dishwasher that was pretty new as it was. The dishes weren't getting clean, checked it out and found out the chopper was broken. Works great now with clean dishes.

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.