JCSP38DN1WW General Electric Range - Instructions

First replaced the 8" burner element-still did not work.
second: replaced the TERMINAL BLOCK KIT still did not work.
third : finally replaced switch: very easly-make sure you do not take off any of the wires on the back of the switch-take new switch and replace each wire on the same location than remove the old switch and replaced wired new on with the two screws.

I turned the power off at the circuit breaker, pulled the stove out from the wall, and removed the plug. I removed the top back panel, and took the burner switch out by unscrewing the 2 screws in the front of the panel. I used pliers to remove the wires one at a time from the bad switch and put them on the good switch. I replaced the new burner switch on the front panel and also, replaced the back panel. I put the plug back in the socket, pushed the stove against the wall, and turned the power on at the circuit breaker.

Red Light Off

followed video exactly

After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove the swith assembley from the front panel.

I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)

had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yum.

1. Shut off power at breaker.
2. lift and prop up burner panel (top of stove)
3. removed three screws along top edge.
4. remove oven door (lifts off hinges easy)
5. remove 4 screws along upper oven opening
6. remove 2 screws up under front panel and pull out upper panel enough to access back of switches.
7. unplug wires (5) one at a time and plug onto new switch.
8. remove the two screws from front holding switch in place and remove old switch.
9. install the two screws attaching new switcj.
10 replace all screws in reverse order.
11. Re-install door.
12 close breaker
easy job any one with any mechanical no-how can do.

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

This electric stove has a lift up top which I lifted to get at the block and follow the wire back to the terminal at the back of the the stove. I removed the 5 small lag screws holding the back in place, removed the backing followed the wires back to where they connected in the Stove On/Off Control, disconnected the two wires from the control and then laid the new part in place rethreading and reconnecting the wires. I reinstalled the block and ran a test to ensure the burner operated correctly. After successful testing I disconnect the old block holder by removing the small lag screw, replace it with a new one that came with the replacement terminal block. I then inserted the block into the new holder carefully rolled up the excess wire and wrapped it in a couple of places with electrical tape and also secured it to the side of the stove, out of the way of operation with electrical tape, put the top down, plugged it back in and put it back in place. All told the repair took about 40 minutes. I was impressed with the speed of delivery, the quality of the product, the instructions for installation and the added bonus of getting a terminal block holder as part of the repair kit! Thank You for making me look like a genius!

I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it complete.

Replaced

First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches. I removed the sensor and disconnected the connector.

pull out stove, unbolt old temp sensor inside stove with 1/4 nutdriver, go to back of stove and take off cover and unhook sensor and hook up new one, put all back together and slide stove back in place.

Just like everyone else it was a simple r&r. However, when removing or installing wire clips I make it a habit to hold the ends with needle nose to prevent any: "snap!" ooops! However to prevent burning the element in the first place, it is strongly suggested to push that broil button twice so that it is set to low temp. It is too easy to use the high setting which will shorten the elements life by 40 - 60 %. Also, keep the oven door partially open when using the broiler. Like the manual tells you!!!

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.