HTW200ASK2WW General Electric Washer - Instructions

Unplugged the washer, turned off water supply to washer, using channel lock pliers disconnected hoses to valve assembly, using nut driver removed two screws on back of console, pulled console away from top exposing valve, disconnected wire harness from valve assembly, using nut driver removed two screws holding valve assembly in place, removed defective valve assembly, transferred foam spacer from defective valve assembly to new valve assembly and installed new valve in opposite order of removal.

I watched a video on a few times that PartSelect sent me about how to make the switch from the broken lock set to the new one. And it really went just as the video showed. So far things are working.

Put the parts in, turned washer on.....lid lock still blinks, will not operate. Suggest the control board that sends the signal to the solenoid lid lock switch is defective. Buying a new washer, scrapping this one.

Unpluged the washer first got as much water out of the drum as possible the leaned the washer over forward and let it rest against something removed hose clamp from pump side and removed the drain hose from pump remove plastic cover and unplug pump push tab and pull remove bolts from pump remove pump install all components in reverse be sure to replace pump to drum seal as well

Once I determined it was the drain pump, (by taking off the drain hose and letting it empty by gravity, then running the spin cycle which worked ok) I ordered the part, got confirmation from PartSelect.com that it would fit my washer. I removed the old pump taking out the 6 screws needed to hold it and the cover in place and unplugged the electric connector. I installed the new pump from PartSelect.com using the same cover and 6 screws and electric connector. I reconnected the drain hose and the washer has worked perfectly since then!

Unplugged the machine, pulled it away from the wall, didn’t have to disconnect water lines, set the parts out on the counter as I went over the instructions a couple of times, followed the directions, plugged it back in, worked perfectly again.

any electrical device unplug the power cord. I followed the instructions the best I could understand them. but once the part was removed I took pics from my cell phone of how the wiring ran, and also what other connections I had to undo. all connections were made, connected the hot n cold hoses, plugged into the washer no beeps or sounds as before opened the hot n cold water valves, and the tub was being filled with water. could not turn on the washer, no lights or beeps... so I gave up I spent too much time on this machine and money too, hope to get an RMA for the Lid Switch assembly

I replaced the Pump Drain assembly. It was very easy. Removed 3 bolts and disconnected the electrical wire harness and put new one on. It works great.

Unplug the cord and shut off hot and cold water faucets.

headache avoidance: The male threads of the inlet valve are plastic. Gently turn the female hose ends onto them at the kitchen table with the eventual position in mind then tighten.

1. Remove 4 screws holding shiny metal backplate w/ 1/4" socket (easy)
2. Pry tabs loose, top of plate (easy).
3. Pull electric leads from 2 solenoids (easy).
4. Remove 2 long screws holding upper painted structure (easy).
5. Remove 2 screws holding valve in place (easy).
6. Tilt and slide the valve loose and pull it out (easy).
7. Replace valve and reverse steps 6-1.

n.b. no inside water tubes; water drips straight into tub

Also, an hour should be enough. I spent more time than needed guessing, dealing with a few issues, opening the machine again, starting over, etc.

ps. I guessed at the age.

Look it up on YouTube to see how to repair the problem. Unscrewed the necessary screws. Took apart the top, pop open the loader replace the bezel. Put everything back together again. Was simple.

Lift the cover, undo too screws, Slide out broken part, slide in new part put in the screws and close the lid.A piece of cake.

Thank you for the super fast service on Christmas eve no less!

Took top of the washer then took one rod off at a time and replace with the new one, the back two are a little bit harder to do but it works great now.

>Change 4 rod & spring, (2 red, 2 blue) and
>LEVEL THE WASHER
(this was the initial cause of the failure!)
>clean tub

Follow the super simple, precise instructions and it is very easy. Only harder part was unclipping the front of the lid.

We changed the circuit board once, and the door latch mechanism twice because we ordered a faulty part. Then we had to hire a service man to program the circuit board, and to inform us that the door latch mechanism was faulty.