HDF330PGR3WW Hotpoint Dishwasher - Instructions

Took off the kickplate, diconnected the wires and removed the whole door by lifting straight up, removing spring wires from hinges. Once door is disconnected from the machine, removed one hinge by removing bolt. Slid gasket into place, secured hinge back in place, then reconnected wires at bottom, replaced hinge spring wires and slid door back down onto hinges. Now that we know how to do it, could do it in 15 min to half hour.

this was ordered 4-9-21 and I have yet to receive it. Its difficult to explain the installation when you haven't received the main part. I paid for this but you have not shipped it. Very poor customer service.

I found it online! There were step by step instructions that were easy to understand. I have never had to do anything like this in my life, only recently had to start doing everything around the house myself due to husband's illness.
The repairman came out, charged me $100 to determine what the dishwasher needed & left me with the part number. He was going to charge me $389 to install the part and they were over charging for the part. The repairman suggested I just get a new dishwasher.
I ordered the part from the website at 1/2 the price that the other place charges and found it on line. With the step by step instructions and the online page, I successfully installed it MYSELF. Saved me a ton of $$.
I LOVE the website
Thank You!!!!

Could not do the repair. The incorrect service rack was shipped. It was a different model than what was ordered. It was a different size and would not fit. Had to ship it back at my own expense. Service rack was $77.03 and that has been reimbursed. The return shipping cost to me was $43.75. That expense still has not been reimbursed. I do not want to risk ordering another service rack and risk having to go through the same type of service again.

It was a simple as: attach and done!
There is a ring on the part that tightens clockwise to the nipple that sprays out the water that it rests on. Twist clockwise and you are done!
It is a mystery how it was unattached to begin with but not a problem in the end, it was easy to fix!

Thanks for sending genuine GE parts!

I fixed this issue by replacing the Dishwasher Tub Gasket (PS11774412) and the gasket on the bottom of the door (PS11700870). Replacing the tub gasket is very easy and straight forward. You just pull it off and put the new one on. The door gasket was much more complicated. See the steps required for replacement below:

The * indicates the part number in the diagram I am referencing

1. Remove the Toe Kick Assembly (*759)
2. Remove screws holding dishwasher to counter and pull the dishwasher out
3. With door shut, disengage the springs on both sides from the arm hinge assemblies *800 (I did this by taking the rope off the pulley hinge *734)
4. Disconnect the wire going from the dishwasher body to the door (there are two or three supports for the wire that need to be removed for it to come free)
5. Open the door about 15 degrees and pull the door upward (only one angle will work for removing the door)
6. Place the door on its front on the ground
7. Remove the two screws (*745) that hold one of the arm hinge assemblies to the door and pull the hinge away from the door (you don't need to pull it all of the way out)
8. Pull the old gasket out to the side and install the new gasket

Terrible! Bottom rack was wrong... original was discontinued. Fork and knife holder did not fit in original location. Parts company new this and still processed the order! Disaster!

Replaced floating seal. Un plugged and Pulled washer out from the counter and laid on its left side. Pull pump out of seal by hand. Straight screwdriver to lever seal out of fitting. Clean hole and wipe seal then push into hole. Reinsert pump reverse install.
To make it easier I previously extended the water supply hose to nearly 8 feet so did not have to disconnect it.

Don't remove the door! Unscrew the bolts at each lower corner of the door(this is how the door is attached to the hinges so it is now free). Then open the door fully and slowly pull the door toward you a few inches. This slides the door up the hinges and allows just enough room to slide the old gasket out and and slide the new one in. Then slide the door back down the hinges(pushing it away from you, back into place). Then simply close the door and reinstall the bolts at the bottom corners and all done! I watched several videos and believe me, removing the door to replace this gasket does nothing but turn and small quick repair into a large lengthy one.

Ordered both a top and bottom rack. It's as simple as pulling the old ones out and sliding the new ones in. There's two small clips for the tops rack that need opened and placed the new rack. As well as the plastic blade. No tools were needed for any of it. Would highly recommend these as replacements if someone needs them. Couldn't be any easier.

Thanks to this site for saving me about 150.00.This is my third repair with parts from your company. Thank you.

There was no repair -- it was a simple snap-in replacement of lower spray arm assembly. The shaft holding the lower spray arm in place is plastic so of course it broke when a utensil blocked the arm from spinning.

I appreciate the Parts Select company for enabling me to purchase a replacement part though that allows me to keep my old dishwasher working.

The dishwasher had been installed before we added 3/4 oak floor, so I could not pull the dishwasher out from under the counter. That will be a major project when the dishwasher dies.
To remove the door, I removed the two 1/4 " screws on the right and left bottom of the door. I used a box wrench since that was the only way to reach them. One had corroded due to a leak. it took some coaxing but finally came loose. The hint about opening the door 27 degrees and propping it open with two Allan wrenches through the hinge holes was very helpful. Then I lifted the door a little and gently pushed toward the counter releasing the door form the hinges. I took the door off to find a leak and found the right corner edge of the inside tub had cracked. Not sure how this happened. I cleaned and sanded the crack area and used J-B Weld to epoxy the crack. Replacing the gasket was easy. Slide out the old, slide in the new. Everything went back together smoothly. If I hadn't needed to repair the tub, the hint about opening the door all the way and sliding it out part way might have worked to change the gasket. Note. Unlike a stove door the dishwasher door is not that heavy.

I removed the old gasket and installed the new one in the same position as the one I removed. I had to feel with my fingers for the ridge to insert the gasket so that it would hold. I must admit that I was skeptical that it would work (the old one didn't even seem very damaged). I ran a cycle and there was no more leaking. We've been using the dishwasher ever since with no issues of leakage.

Very satisfied customer.

All we had to do was order the top and lower racks and put them in. It was way less work and cheaper than having to put in a new dishwasher.