Back
Back
Keep typing for more specific results...
Models > HDA2100H50BB > Instructions

HDA2100H50BB Hotpoint Dishwasher - Instructions

All Instructions for the HDA2100H50BB
46 - 60 of 222
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
dishwasher did not start
Took out interlock switch (two leads) and replaced with new one. As simple as that.
Parts Used:
Dryer Switch
  • Lawrence from ROLESVILLE, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
7 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rinse Agent Tank Leaks
The following steps were performed: 1) Disconnect power to the dishwasher 2) Unscrew all the screws on the inside of dishwasher door. 3) Remove outside plate on bottom of dishwasher. 4) Separate the dishwasher door after all screws are removed and pull out the old dishwasher rinse agent tank. There is a screw that needs to removed that holds the tank in place as well. 5) Snap in the new rinse agent tank and tighten screw in that holds tank in place. 6) Gently put the inside door back in place. Make sure all the holes line up correctly. 6) Put back the bottom plate of dishwasher. 7) Turn on the power again. You have now completed the repair.
Parts Used:
Dishwasher Tank Rinse Aid Assembly Scr 818 B Por 1/4 (Stainless Steel)
  • Paul from Lithia, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
6 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel had melted and support cracked
Removed the lower rack and installed new wheels with clips
Parts Used:
Dishwasher Lower Rack Wheel Kit 8 Pack
  • Tom from UPPR CHICHSTR, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Three of the 8 wheels broke.
The newly purchased wheels have a little different design and could be installed in a matter of few seconds.
Parts Used:
Dishwasher Lower Rack Wheel Kit 8 Pack
  • Asok from HELOTES, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rinse Aid Fill Cap melted because it landed next to the heating element because it wasn't screwed in
Simply screwed in new cap
Parts Used:
Dishwasher Rinse Aid Fill Cap
  • Helen from Carol Stream, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher leaked
Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.
Parts Used:
Dishwasher Door Gasket (White)
  • Robert from Colleyville, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rusted Racks
Replaced lower rack with new. Upper rack removed front stoppers, removed old rack, slit new rack in and replaced stoppers. Total time about 15 mins.
Parts Used:
UPPER RACK LOWER RACK
  • Eduardo J from San Angelo, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not start
Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell
Parts Used:
Dryer Switch
  • Dameon from SMYRNA, DE
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Latch was broken so dishwasher wouldn't run
I watched several YouTube videos on how to make the repair. It looked very easy but sometimes professionals, because they've done it before, don't point out small tips that would help a DIY homeowner. The latch goes easily into the inner door slot but there's nothing to hold it there. The videos show the inner and outer door being closed together without showing that you have to hold the latch in place while bringing the outer door up to meet the inner door. Any movement of the inner door makes the latch fall out. So I would say it took me 5 times longer to do this repair than it would if I was doing it again.
Parts Used:
Dishwasher Door Latch Kit
  • Rhonda from CANTON, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing wheels
The wheel kit came with axel's to support them. They snapped in place in seconds. No instructions provided, but installing method was obvious.
Parts Used:
Dishwasher Lower Rack Wheel Kit 8 Pack
  • Denise from PALERMO, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The telescopic part of the washer was broken.
The part came in as ordered. After removing the dish rack, I loosened three 1/4" screws (two on the strainer basket and one at the base of the spray arm. I had to slide the rubber hose down and back to disconnect the base which I did by turning counter clockwise. The new one went in by reversing what I just described. Other than two of the screws being difficult to reach, everything worked fine.Thanks for your site.
Parts Used:
Lower Spray Arm
  • Jeffery from DOUBLE SPGS, AL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set, Wrench set
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wornout rack
I took out the old one and put the new one in.
Parts Used:
LOWER RACK
  • John from Yuma, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Damaged rinse agent dispenser
Unscrewed old one and installed the new one.
Parts Used:
Dishwasher Rinse Aid Fill Cap
  • Ralph from McMinnville, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
7 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Put lower rack in
Took old rack out put new rack
Parts Used:
LOWER RACK
  • Robert from Hillsborough, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken off end caps, top would slide off, frustrating.
did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.
Parts Used:
Dishwasher Rack Slide End Cap
  • Paul from Blairs, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the HDA2100H50BB
46 - 60 of 222