GU2400XTPS7 Whirlpool Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Friction sleeve
-
Dave from PALM BAY, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
14 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Poor seal on old gasket caused water to leak during dishwasher operation.
I simply pulled out the old gasket and pushed the new one in with my fingers. I had to trim about an inch off the length with a utility knife. The seal is nice and tight now and we have no more water leakage.
Parts Used:
-
Jennifer from Edina, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
15 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water not draining from the dishwasher
I watched the video and this was the easiest repair ever. Took longer to disconnect and reinstall than it did to change out the pump. Highly recommended watching the video
Parts Used:
-
Frederick from BIG PRAIRIE, OH
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
13 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Sart button would not respond.
Removed the 6 screws holding the panel on. Then remove the control board to expose the wiring for the panel,and disconect. Connect new panel, reconnect board, replace screws. Done.
Parts Used:
-
Chris from Princeton, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
19 of 32 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dishtrack wheel came off the track and fell into the dishwasher and melted
I snapped on the new part onto the track. It was that easy! :) Thank goodness the part was available from Part Select!
T. Edwards
T. Edwards
Parts Used:
-
Timothy from huntersville, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
14 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain Pump was giving off a burning smell. When I pulled the dishwasher out it had some light smoke coming from the Drain Pump
Shut the power to the dishwasher off. Pulled unit out from under the counter top and raised the left hand side up for easy access. Disconnected the wiring, undid the clips, turned counter clockwise and removed. Reversed the order for installation and Connected the power. Ran several cycles successfully. Problem fixed. Burnt out water pump. Good as new if not better so far. Easy item search, Fast Shipping, Quality Part, Fair Pricing. Thank You Partselect.com
Parts Used:
-
Armand from N STONINGTON, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
13 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat. Replaced thermostat
Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.
Parts Used:
-
Tim from BURTONSVILLE, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
12 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
clean light flashing 7 times would not run
removed screws holding dishwasher to counter top,raised leveling pads,pulled dishwasher out, unplugged wiring,removed hold down nuts from inside dishwasher and installed new heater element, this was all easy the hard part was finding the code to reset the dishwasher there was no paperwork inside the dishwasher although there was an empty plastic holder.The code that worked for my model was with the door open to push the normal wash button then the high temp button three times as fast as you can within four seconds then close the door. It worked and reset the dishwasher which ran a short cycle then shut down as normal and is now working fine.After doing this select the beverage of your choice and relax. Hope this helps someone.
Parts Used:
-
Mark from Winchester, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable), Wrench set
14 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No lights on control panel
-
Alex from Costa Mesa, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
13 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper Spinner in Dishwasher
The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retainer in but I drop it into dishwasher so you have to me very careful
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.
Parts Used:
-
Larry from Abington, MD
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
12 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor was very loud...........bearings in motor were beyond repair
-
Mark from Plymouth, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
17 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rollers and clips on botton dishrack were broken
I pulled off the old clips and easily replaced them with the new clips and popped on the wheels.
I replaced 8 clips and 8 wheels in less than 15mins
I replaced 8 clips and 8 wheels in less than 15mins
Parts Used:
-
Diane from Waltham, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
20 of 38 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Power
The first thing I did to repair my diswasher was call a repair company. They wanted $175.00 just to look at it, so I scheduled an appointment. Then, I did an internet search for dishwasher repair. I learned about bi-metal fuses, and how to check them. I found my bi-metal fuse was bad, so I ordered a new one through parts select. My part arrived in two days. I installed it easily, and the dishwasher worked. Finally, I canceled the repair appointment.
Parts Used:
-
Rodger from Wilmette, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
13 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Lights Were Flashing
Shut off circut breaker. . . Removed 6 screws. . . Lifted cover over control board. . . Removed old control board. . Installed new board. . Replaced cover and the 6 screws. . Turned on circut breaker. . . Turned washer on. . . . It worked. Thank you for the quick delivery!
Parts Used:
-
HENRY from SALEM, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
15 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
friction sleeve broke
Unscrewed the top of the dishwasher from the counter top and slid the appliance out part way in order to reach the door spring. I loosened he spring from the bracket then slid the sleeve over the bracket. I reattached the spring to the bracket, slid the dishwasher back in and screwed it to the top just like it was prior to removal. Easy as pie.
Parts Used:
-
Roxy r from GERMANTOWN, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!