GTW330ASK2WW General Electric Washer - Instructions

I watch a YouTube video with the same problem and follow each step

I unplugged the machine from the power source and removed the drain hose from the back and allowed any remaining water to drain out of the machine. I then tipped the machine back so that I could work underneath it and secured it in that position. I removed the old drain pump assembly by first disconnecting it from the outflow hose, then removing the three bolts which held the motor housing cover on and disconnecting it from the power source. This part was the the most difficult and time-consuming as the wires are plugged in very tightly but once those were separated, it was just a matter of unscrewing the drain pump assembly from where it was anchored to the underside of the washing machine. I simply reversed those steps to install the new one and it was in place within 10 minutes. Set the washing machine down in the correct position, reconnected the drain hose, and plug the machine in. I did reset the fault codes by using the manual found taped to the underside of the machine, but this was very simple to do and only took a few minutes. I’m not sure if it was necessary to do that step at the machine works perfectly now. I am a woman and found this repair very easy to do.

The most important item I learned is the original lid switch is no longer available. It has been replaced with the entire Lid Switch Assembly. I read the new switch is magnetic versus the old which was mechanical. The kit comes with everything you will need (switch, wiring harness, lid lock bezel and instructions). I found the written instructions to not be the easiest to follow. However, I found someone had done a YouTube video on the replacement which made the repair easy (under 15 minutes). Although I did the repair by myself, a second person would be handy to hold the washer cover and controls while changing the wiring harness. When testing the new switch, remember to test during the Spin cycle.

Dipped water out as much as possible,tited washer at a 45 degree angle and propped it up. Took the 3 bolts out holding the pump assembly and the 3 bolts holding the belt guard.Unplug wire connecter,pull out assembly and than pull drain hose off of assembly. Reinstall the same as you take apart. Was a easy fix, and worked as it should.

My son in law did it for me

First thing is to download and print the programming instructions for the new control board. The instructions for downloading come with the control board. The control board fits multiple models and has to be programmed for your particular model. Unplug the washer and pull it out enough to work from the back. Remove the main control knob by pulling it off. At the top back use the nut driver and remove the 4 screws holding the metal cover. There’s a ground wire attached to the inside of the panel that doesn’t have to be removed. Let the metal cover dangle. Remove the two screws that hold the top control panel. They are located at the ends of the control panel. Slide the main control panel towards the back of the washer above 1/2” and lift it up and roll towards the front of the washer which puts the main control board in a position that allows removal. Unplug all of the connectors. Remove the 3 or 4 screws holding the plastic board stiffener, unsnap the two posts holding it to the control board and remove it. Remove the main control board. Compare the old and new board. If they match install the new board in the reverse order of removal. After reassembly and putting the washer back in place, plug it in and follow the programming instructions. My replacement of the control board went very well except the first new control board didn’t work. There was one complete zone that didn’t function. I called Parts Select and they sent me another control board which worked and the refunded the cost of the defective board but I was out some shipping expense.

first disconnect the electric power cord. Disconnect the incoming water lines. Tip washer up or better yet flat on the floor where bottom is completely exposed. Remove bolts holding guard over belt and motor. remove bolts [2] holding clutch arm into plastic bearing, remove old belt will slide off pulley, remove bolt holding pulley to shaft, calls for a puller but I applied pulling pressure while working back and froth; no problem but could have been. chance clutch bearing and reverse the process to working order. I would recommend wearing cloth or vinyl gloves once the guards are removed for the pulley and old belt has a lubricant that is somewhat messy but cleans up easy.

Removed the center agitator to clean it - had black mold and pink soap scum buildup underneath that you couldn't see or clean without taking it apart. Removed the bolt with ease. Upon tightening the bolt back in place, the bolt sheared in half, leaving the lower half threaded in place and the head in the socket. Had to use a drill bit and drill out the lower half of the bolt completely. Ordered the replacement bolt and reassembled everything in less than 5 minutes. Replacement part was perfect - hopefully it lasts longer than the original bolt.

unplugged old part plugged in new, took about 2 minutes.

this is a great web site, I didn't have to wait for a serviceman to come. and maybe not have the part and come back again. ........thanks

Turned washer on to its side. Removed belt cover, three screws. Removed old belt. Cleaned both pulleys thoroughly, removing all traces of oil. Cleaned grooves thoroughly on motor pulley with small screwdriver. Installed new belt. Replaced cover. Turned washer upright.

Locked garage door.
Removed hoses after shutting off water.
Removed 4 10mm bolts and removed old valve and replaced.
Reverse the process.
Total time about 5 minutes.
Drank beer and then declared to wife after 30 minutes that the problem was solved.

Attached the lid striker with 2 screws to hold it in place

I just took old one out an put new one in

My son installed the new parts.

Not knowing for sure how to fit it I went to youtube for help watched a few videos and tested different things until I hit the right one .Moms washer is fixed.replaced lid lock,motherboard and pump I'm sure I don't need all those parts because when I found the code for the lid lock it started working