GT218 - Instructions

It was easy breezy!! I felt like an empowered woman that I did it myself. I simply removed the old shelf supports with a screwdrive and inserted a screw thru the new supports and screwed them in.

Once I identified the problem, Partselect's web page made it easy to find a replacement part. The Housing Control unit was easy to remove as it had one screw in the middle, by the temprature control section, and two screws to either end. The center screw required a philips head, but the end once did not need to be removed. The unit could simply be slid out and the wiring is easy to disconnect. Then it was simply a process of inserting the components from the damaged Housing Control unit, to the new one. If you treat it like a "puzzle" you'll get the results you want with out the aggrevation that it could turn into.

By sliding athin screwdriver blade down the side of the old switch the expasion prong that hold the switch in place was compressed enough to allow the switch to come out easlily. Plugged in new swithc and snapped in place. Plugged the refrigerator back in and light has worked great sense!

The gasket is sandwiched between the main door and the shelf assembly.

What holds them together is 42 1/4in hex head self tapping screws that run along the edge (each one is finger tight).

I would highly recommend a power drill with a 1/4 hex socket to remove the screws. It makes things much faster. Be careful when screwing the screws back in with the power drill(you only want them finger tight). If the screws are too tight,the gasket will bulge out in places.

At first the seal may feel weak. Keep the door closed for a couple of hours and the seal should improve.

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

My brother came up and installed the part.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

After unplugging the appliance, I unscrewed the screws in the bottom and the back of the freezer compartment and un-clipped the connector for the ice machine, which i do not have installed. I clipped the pink and brown wires and replace the switch with the new switch. unfortunately, the appliance is still dripping water from the freezer compartment. It worked for a couple of days then stopped working. Still looking for a true FIX.

I opened rear wall inside freezer (two screws) cut the wires on old thermostat and removed it. Then I attatched the new thermostat to the existing wires using wire nuts and electrical tape and slid it onto the copper tubing. Re-installed the rear wall. Freezer works like a charm and the refridgerator is also colder. Job completed in twenty minutes and Tim Allen has nothing on me. Mike Milne

Ok, first off, I am a girl-with absolutely no 'fix it skills" whatsover. My husband had pointed out the problem to me the second time the fridge started to get warm. I ordered the part (wrong one first time), then reordered the correct part. I emptied the freezer, defrosted the coils, installed the part. Put back together-all of it took about 15 minutes. I am still oh so very proud of myself.

No repair needed. I had only to wash the new ones and use them.

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Ordered new shelf on a Tuesday night. Part shipped out on Wednesday, received and installed on Friday. It doesn't get any better than that!

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

took cover off back of inside of freezer undone the thermostate and put back together