EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
Back
Back
Keep typing for more specific results...
Models > GSDL322F01BB > Instructions

GSDL322F01BB General Electric Dishwasher - Instructions

All Instructions for the GSDL322F01BB
61 - 75 of 374
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Leaking water pump
Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.
Parts Used:
Impeller and Seal Kit
  • John from Palatine, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
7 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No water able to come in or out.
Repair is super easy and anyone can do it in no time!
At first my fear was that it was the pump, but after reading through the trouble shooting here it narrowed it down to the water inlet valve. The new valve even came with easy to read and understand instructions. I had it fixed in less time than it took my wife to make us lunch lol.

2 screws hold the mount bracket in place. Just remove the screws, remove the c-clip that holds the secondary/small water line on, pop the hose off then remove the main water inlet line [ its the bigger line with the brass fitting ] I only needed a pair of pliers for this. Reinstall the main water line into the new valve, but make sure you use pipe tape on the fitting or you'll have a water leak. Reinstall the secondary water line and reclip the c-clip using pliers to squeeze the clip. Hold the valve in place and reinstall the 2 mounting screws. That's it your done !!

This is the second time I've used partselect, and they are hands down the best !! Other sites would have you buying part after part until you happened to get lucky and get the right one. Not here, they help you figure out just what you need and nothing more.
Great people and fast service !!
Thank you once again.
Parts Used:
Dishwasher Water Inlet Valve
  • Victor from Raymond, NH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Wrench (Adjustable)
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
spray arm falls off
Turn off power at breaker box.
Remove lower covers and 2 screws into counter top.
Verify sufficient length on water and electrical connection to allow sliding dishwasher out approx. 2/3. I disconnected the electrical at the j box on the dishwasher. If you must disconnect the water line, shut off supply, usually located under nearby sink, and provide a rag or sponge for small amounts of water left in supply line.
Carefully pull back the insulation to expose two screws on top where water line runs into the center.
Pull the top tray part way out and reach in to hold the spray arm while removing the screws. The spray arm will easily drop out.
Hold the new spray arm in place making sure the raised screw posts push into the holes, then reinstall the two screws. Done. Pull insulation back into place, retape if necessary. Reconnect electrical and water if necessary.
Slide unit back in, checking alinement. Rescrew to counter top and reinstall lower covers. Task complete. 15 mins if prepared. 30 mins if both elect. & water are disconnected and you are somewhat hesitant.
Parts Used:
Third Level Spray Arm
  • JAMES from AUBURN, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dispenser cap would not stay in place because it had melted
First I opened the package and screwed the new dispenser cap into place.
Parts Used:
Dishwasher Rinse Aid Fill Cap
  • Patricia from Clifton, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No lights pn dishwasher
The symptom was that none of the dishwashers light came on – it was totally dead
With this repair the important thing was making sure I was replacing the right part. I also tested parts in order to avoid disassembling more than I needed. I checked the following:
1. Circuit breaker
2. Electricity was getting to the connection box underneath the dishwasher. (Require removing panels between DW door and floor).
3. Next I disassembled the DW inner door and checked the switch. Power was getting to the switch. When depressed, power was go on both sides of switch.
4. I pulled out the electronic control assembly (ASM) and checked that power was getting to the ASM; it was. (Note: be careful about what you touch, there is 110 volts out in the open).
5. I pulled the ASM from the enclosing plastic box that surrounds it. I looked at the circuit board to trace where power went from the connector. Not surprisingly, it went through a fuse then to a transformer.
6. I checked the fuse two ways: I checked it hot: power was getting through the fuse. I also unplugged the power and checked the resistance. The fuse was good.
7. Set the Volt-Ohm meter back to 300 Volts AC range – do not risk putting 110 volts into the ohms setting.
8. 110 volts was getting to the primary side of the transformer. There was no voltage on the other side.
9. I unplugged the power and checked the resistance of the primary side of the transformer. It was “open” – meaning a wire is broken inside the transformer.
10. This confirms the problem in on the ASM board. If I knew the voltage on the secondary of the transformer and radio-shack had such a part I guess I could try unsoldering it and replacing it. But I didn’t know that and there were signs of water corrosion on the board so I replaced it.
11. PartsSelect made the look up easy. Delivery was fast. The DW now works again.
Parts Used:
Dishwasher Control Board
  • Paul from Suwanee, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Disrack was getting rusty
Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.
Parts Used:
LOWER RACK
  • Nelson from Oroville, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Severe lwater leak around door
Removed door panel. Removed old door seal and cleaned seal recess. Installed new seal. Replaced door panel on door and ran a cycle to check for leaks. Readjusted door latch to correct small leak. Ran another leak test. Job complete and wife is happy!
Parts Used:
Dishwasher Door Gasket (White)
  • Merle from Boulder, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor/Pump Siezed - Only Getting A "Humming" Sound
Only getting "humming" sound from dishwasher. Although water had filled the dishwasher tub, pump/motor would not operate. After some research, figured the motor had siezed and I had to replace the pump/motor assembly as mentioned on this site. The kit came in a couple days and I reserved a Sunday afternoon for the repair which I had never done before. Hardest part of repair was unhooking and removing dishwasher from under counter and then getting it back in proper place. I would suggest providing some instruction within the repair instructions showing how the dishwasher is installed or how to remove it as I had never installed one so I was not quite sure what screws etc I needed to remove on the dishwasher itself to start to remove it? I was able to find the original installation instruction for the dishwasher and found that all you had to do was remove two screws from the inside top of the dishwasher which were securing it to the bottom side of the kitchen counter and then the whole thing just slides out. Once removed, turned dishwasher over to access bottom where pump/motor is located. After determining which diagram to use with the instructions, proceeded to replace the motor/pump assembly. It came out easily after wrestling with some corroded bolts/nuts and the existing pump inlet and outlet hose clamps. Mine were old and worthless and no new ones (3-4") are supplied with the kit. Had to run to hardware store to get new hose clamps for the inlet/outlet of the pump before intalling new one. Suggest new hose clamps be provided with the kit. Only thing that was not too clear in instructions was when reconnecting power wiring harness to motor. By looking closely at the instruction diagram I was able to locate what looked to be the right power extension harness from the bag of parts and attach it to the existing power wire harness and the new motor. Suggest also that you somehow better distinguish or identify the proper way the power wire harness should be fastned to the motor? The existing power wires were both the same color and both the female and male connections for the power at the new motor were identical leaving you to guess which wire goes to which connection. After re-installing dishwasher, put about a gallon of water in bottom of unit prior to starting and then put it through a few cycles. It has been working just like new. Suggest having a helper when removing and re-installing dishwasher from under kitchen counter to assist with the power cord, water line, drain line, and help to turn the dishwasher upside down and right side up again.
Parts Used:
Dishwasher Motor And Pump Kit
  • Scott from Oklahoma City, OK
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench set
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor and pump kit was easy, but the panel was a bit difficult. Lining up pnl to mount and adding the nut plates.
Remove two front mount screws from counter top
Lower dishwasher floor feets
Pulled electric leads cover and disconnect electric leads
Pulled dishwasher out and leaned on it's back
Sorry missed a step turn off breaker to dishwasher
Removed water line and drain hose
Removed motor/pump using only a socket setup and cross tip screw driver
Installed new motor/pump using same tools as removal
Stand dishwasher back up push back into space and reconnect all item mention in removal
Turn back on breaker
Ops check dishwasher
Done.
Parts Used:
Long Front Panel Dishwasher Motor And Pump Kit
  • Roderick from SNELLVILLE, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rinse Aid Fill Cap melted because it landed next to the heating element because it wasn't screwed in
Simply screwed in new cap
Parts Used:
Dishwasher Rinse Aid Fill Cap
  • Helen from Carol Stream, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
poor dish washing
Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.
Parts Used:
Dishwasher Motor And Pump Kit
  • THOMAS from LACONIA, NH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaked at bottom while running
Removed seven screws that held the inside panel to door. removed inside panel to work area and cleaned. After carefully observing the position of the old gasket, it was easily removed and the new one but in its place. Replaced the door being careful toalign the handle before tightly securing all seven screws. Repair worked, no more leak.
Parts Used:
Dishwasher Door Gasket (White) Dishwasher Gasket Insert
  • Robert from Wyckoff, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor froze up on dishwasher
Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.
Parts Used:
Dishwasher Motor And Pump Kit
  • Raymond from Oshkosh, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
"Clean" light inoperative; too much water in bottom; dry cycle malfunction (inside wet, dishes not dry).
REPLACE CONTROL BOARD - Turn off circuit breaker. Take out lower rack. Remove inside door panel (seven Phillips screws). Hold outside door panel (control board location) in place with bungee cord. Remove push lever (two screws) to facilitate removal of control board. Disconnect control board connectors (five, I think). Remove old control board (two screws and plastic clips). Install new control board (clips, connectors, and two screws). Re-install push lever (two screws). Re-install inside door panel (the main contol lever alignment is a little tricky), seven screws. Remove bungee cord. Put lower rack back in. Turn on circuit breaker. Test dishwasher. Worked perfectly, just like new. Normal amount of water in bottom. "Dry" cycle normal. "Clean" light comes on and stays on until door is opened i.e. normal operation. "Delay" feature also works normally. Dishwasher may last a few more years. Cost of control board: $120 inc. shipping.
Parts Used:
Dishwasher Control Board
  • Rex from Basking Ridge, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher leaked
Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.
Parts Used:
Dishwasher Door Gasket (White)
  • Robert from Colleyville, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GSDL322F01BB
61 - 75 of 374