GLMV168KB001 General Electric Range - Instructions

Removed bottom cover of microwave, involved removing 7 screws, removed turntable motor, involved disconnecting wire harness plug, and 2 screws, connnected wiring to new motor and reinstalled with original hardware

I removed 4 screw from the under carriage of the microwave then, removed the 2 screws from the motor, replaced the motor and replaced the screws. It was so easy it took only 4 minutes to perform, better than replacing the whole unit (microwave) and less expensive too. i only wish it was made in the US, I wouldn't mind to spend a little more.

1. Pried off the choke on rear of door to expose screws to door handle. 2. Using Phillips-head screw drive, removed the two scews to door handle. 3. Removed cracked frame from door - a bit difficult because frame is held in place by plastic tabs. 4. Removed door latch assembly from cracked frame and installed on new frame. 5. Refitted door handle to new frame. 6. Snapped new frame in place - again, somewhat difficult because of plastic tabs. 7. Replaced choke to rear of door - be careful because exact positioning of the choke is required and misalignment might crack the choke. 8. Enjoy saving over $100 in labor.

Removed screws and old parts. Fitted new part to door and put screws back in.

removed electrical wires, unscrewed holder, inserted holder, attached wires, added bulb, and put cover back on.

My microwave was squealing horribly and replacing the turntable motor (SUPER easy btw) didn't fix it. So I figured it was a spun bearing or bushing in the cooling fan (spoiler alert -- it was!). Installation was simple and did NOT require removing the cabinet-mounted microwave from its position above our stove: Unplug microwave, carefully unscrew the 2 screws holding the vent grate above the door, remove the grate, then unscrew the one screw holding the top of the control panel to the case. Carefully pivot top of control panel down and unhook it from the case (at the bottom of the control panel there are two little legs or extensions that insert into slots in the case). Then disconnect the 3 or 4 wires that attach the control panel to the wiring harness (I marked them each with tape so I would remember where they go, but you can just take a picture with your phone). Set the control panel aside. Where the control panel was, you will be looking at the fan, with a bunch of wires between you and it. Take another phone picture for reference, just in case. Disconnect the various wires, starting at the top right and working your way around clockwise. I marked each wire with a piece of tape and a number, starting from 1 and working my way around an imaginary clock face. I think I got to 12 and then the last two (sort of buried in the middle) I labeled as "0" and "-1" but you can use any numbering series you like. Once the wires are all disconnected you can gently push them aside and unscrew the two screws holding the fan assembly in place, and disconnect the fan wire. Then gently maneuver the fan assembly out the front of the case. Installation is simply the reverse of this simple disassembly process. Voila! Back to a nice quiet microwave.

This repair was one of the easiest I've ever done. I turned off the power to the microwave at the breaker, lowered the bottom panel by removing the screws, disconnected the wires to the old motor, pulled it out by removing two screws attaching it, attached the new motor with the same screws, connected the wires to it and that was all. The turnable has worked perfectly (and quietly) since.

First I figured out how to take the door apart to remove two hidden screws, once that was done it was easy to install the new part. The part came extremely fast and worked well. The picture with each part labeled helped too!

Removed control panel disconnected old capacitor installed new and returned the leads back on to the new. replaced control cover and tested

Placed the screws in the proper areas, used the screw driver to tighten down and I was in business with light to spare. I am happy to have found the proper screws.
Thank you.

Phillips screws on bottom panel allowed me to install new socket and put electric connection back. Secured bottom panel and that was it.

Had to take to a local glass shop for sizing and to remove sharp edges. Will never order again.

Turned the power to the unit off. Removed seven- (7) small screws from the base plate, not removing the rear screws. The plate dropped a few inches allowing me to get to the light socket. I removed one- (1) screw that allowed the socket to be removed. I then detached the two- (2) electrical leads. I now installed the new socket, replacing the leads and the screw along with a new bulb. I pushed the bottom plate back into the up position and replaced the seven- (7) screws. Turned the power back on and we were good to go.

You'll need to use the knife to remove the plastic frame backing from the the microwave door. Be careful when disengaging the tabs so as not to break them.Then you'll need to use a phillips screwdriver to remove the four screws from the door. Remove the damaged handle. Installation is the reverse of the removal process.

Have a microwave that the light and sockets just broke in pieces so I ordered two sockets from this site . The fit perfectly and it was a breeze to install. Took out 7 screws and the plate dropped down, hooked up the little wire which was so simple and bingo I had lite again. I just wished the hold plate came down but it didn't but it was still very easy to install. Will continue to get my appliance parts from this company.