GLGS Frigidaire Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven would not light
Make sure you unplug the oven before you begin. I removed the old igniter. The top wire on the igniter goes to the back of the oven and plugs into a flat blade type connector. Instead of using the twist wire nut I used a flat connector because it was easier to put on and is foolproof. Make sure you cut the plastic insulation off the connector so it does not melt when the oven is in use. I used a wire nut on the other wire and that was it. Very simple and the oven works great again.
Parts Used:
-
Matt from Verona, WI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven would not light -igniter was on
removed shelves and base, removed 2 screws that held igniter on, disconnected wires from gas valve removed protective cover in corner {1 screw}
disconnected plug, removed igniter. This igniter was easier to remove from front of stove on this model
disconnected plug, removed igniter. This igniter was easier to remove from front of stove on this model
Parts Used:
-
Tom from South Amboy, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Socket set
9 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken ceramic burner element
Simple: remove the element by hand and replace new one.
I can't believe how quickly I received my new part -literally next day.
I can't believe how quickly I received my new part -literally next day.
Parts Used:
-
Phillip from Saint Simons Island, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
9 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn’t get up to temperature
I removed the sensor from inside the oven with a 1/4” nut driver, pulled the sensor out slowly and then took the connection apart and found out that the connector was different, I cut the connector off of the oven side and then cut the connector off of the new sensor and wired it together. I am still trying to find the ceramic nuts. My oven is working for now. Very easy fix, just wish there were ceramic wire nuts with the new sensor
Parts Used:
-
Al from THORNTOWN, IN
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven would take forever to heat up, and sometimes not at all. Othertimes it would heat up, but not stay hot for the entire baking time.
First, I unplugged the oven from the wall. I opened the bottom drawer of the oven to see where the igniter was mounted, which was directly under the bottom pan of the oven itself. I opened the main oven door and unscrewed the 2 screws that were holding the pan to the bottom of the oven. Then, I slid the pan back towards the the back of the oven and it popped right out.
There were 2 hex screws that were holding the old igniter on, so I unscrewed them with my socket set. I made sure to pay attention to which wire was the top one and which one was the bottom one coming out the back of the igniter. I pulled off the wire nuts connecting the igniter wires to the wires of the oven. I striped the wires on the new igniter and re-attached them to the proper wires of the oven, using the included replacement ceramic wire nuts. I re-screwed the hex nuts in, mounting the new igniter to its proper place. I put the pan back and screwed the 2 screws back in to hold it in place.
Plugged it back in, turned it on, fired up within 20 seconds. Good as new.
There were 2 hex screws that were holding the old igniter on, so I unscrewed them with my socket set. I made sure to pay attention to which wire was the top one and which one was the bottom one coming out the back of the igniter. I pulled off the wire nuts connecting the igniter wires to the wires of the oven. I striped the wires on the new igniter and re-attached them to the proper wires of the oven, using the included replacement ceramic wire nuts. I re-screwed the hex nuts in, mounting the new igniter to its proper place. I put the pan back and screwed the 2 screws back in to hold it in place.
Plugged it back in, turned it on, fired up within 20 seconds. Good as new.
Parts Used:
-
Jason from Los Angeles, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
7 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven light bulb went dark; it needed replacing
-
Lise from CEDAR GROVE, NJ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
10 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ignitor glows but not hot enough to open the gas valve. It's old.
My Tappan Tail:
Open the oven and remove the racks, turn on the oven light.
Remove two screws in the back to remove the bottom plate. Mine are about 1 1/4 in. long.
Remove one nut holding the butterfly plate in place. Ignitor will be exposed.
Turn off the oven light and unplug oven. Don't drop the plug behind the oven, I was ready for that one.
Drop light or flash light will be needed, it's dark in there. And something to sit on, 16" old plastic milk caddy, I just happen to have one.
Remove the two screws holding the ignitor, don't cut the wires just yet. Take note where the wiring runs. Install the new ignitor. My wires went behind the gas piping.
I cut the bottom wire from the old ignitor first, up close to the ceramic. Wire shield can be reused, slide it over the new wire. Cut the old wire, leave a lot. Trim the new wire to desired length and strip the ends of both and use the ceramic cap and connect the wires.
Do the top wire.
Slide the wire shield next to the igniter, adjust the wires so the wire shields won't slide away from ignitor. With the butterfly shield back in place it's time to plug it in and give it a test.
Nice.
Replace the bottom plate of oven, screw holes hard to find. Had to use an awl to find the holes to line up the screws. I also didn't push the front of the plate down into place until I had the screws started. It helped.
You might think this is overkill, but how many of us have ever replaced the ignitor. Not me.
I do a lot of DIY's. I'll rate this as a 1, easy.
What shall I bake first, cornbread of course. I my cast iron skillet.
Open the oven and remove the racks, turn on the oven light.
Remove two screws in the back to remove the bottom plate. Mine are about 1 1/4 in. long.
Remove one nut holding the butterfly plate in place. Ignitor will be exposed.
Turn off the oven light and unplug oven. Don't drop the plug behind the oven, I was ready for that one.
Drop light or flash light will be needed, it's dark in there. And something to sit on, 16" old plastic milk caddy, I just happen to have one.
Remove the two screws holding the ignitor, don't cut the wires just yet. Take note where the wiring runs. Install the new ignitor. My wires went behind the gas piping.
I cut the bottom wire from the old ignitor first, up close to the ceramic. Wire shield can be reused, slide it over the new wire. Cut the old wire, leave a lot. Trim the new wire to desired length and strip the ends of both and use the ceramic cap and connect the wires.
Do the top wire.
Slide the wire shield next to the igniter, adjust the wires so the wire shields won't slide away from ignitor. With the butterfly shield back in place it's time to plug it in and give it a test.
Nice.
Replace the bottom plate of oven, screw holes hard to find. Had to use an awl to find the holes to line up the screws. I also didn't push the front of the plate down into place until I had the screws started. It helped.
You might think this is overkill, but how many of us have ever replaced the ignitor. Not me.
I do a lot of DIY's. I'll rate this as a 1, easy.
What shall I bake first, cornbread of course. I my cast iron skillet.
Parts Used:
-
Kenneth from MESQUITE, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Temperature in the oven was not consistent
1. Turn off power to the electric oven
2. Removed the two screws in the top side of the oven that hold it into the cabinet.
3. Made a support to set the oven on once you remove it from the wall. Or set it on the floor. You will need help this is not a one person job.
4. Used a Philips head screw drive removed the back of the oven panel. I did not have to remove the whole thing just took out half the screws and the electrical plug for the temperature sensor is right on the edge.
5. Unplugged sensor
6. Took out the two screw on the inside of the oven that holds the thermal sensor in place. Pulled it out the front.
7. Side the new thermal sensor in place replace the screws.
8. Pull the plug out and plug it back in. Check and push the insulation back in place where the thermal sensor.
9. Replace the back and replace the screws.
10. Slide oven back into the wall.
11. Replace the two screws that hold the oven in place in the frame.
12. Turn power back on
Check the temperature
2. Removed the two screws in the top side of the oven that hold it into the cabinet.
3. Made a support to set the oven on once you remove it from the wall. Or set it on the floor. You will need help this is not a one person job.
4. Used a Philips head screw drive removed the back of the oven panel. I did not have to remove the whole thing just took out half the screws and the electrical plug for the temperature sensor is right on the edge.
5. Unplugged sensor
6. Took out the two screw on the inside of the oven that holds the thermal sensor in place. Pulled it out the front.
7. Side the new thermal sensor in place replace the screws.
8. Pull the plug out and plug it back in. Check and push the insulation back in place where the thermal sensor.
9. Replace the back and replace the screws.
10. Slide oven back into the wall.
11. Replace the two screws that hold the oven in place in the frame.
12. Turn power back on
Check the temperature
Parts Used:
-
Cheryl from PRAIRIEVILLE, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
glide bearings came apart due to wife overloading drawer
removed 1 screw from each glide, pulled parts out, replaced parts and screws, slid drawer glides into bearing glides. job done, very easy and fixed problem.
Parts Used:
-
james from evansville, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
10 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken lens over oven light
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
Parts Used:
-
Leslie from Warsaw, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
11 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven light stayed on & smelled like electrical burning.
Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.
Parts Used:
-
Vincent from Brunswick, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
15 of 34 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator Light bulb went out
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Parts Used:
-
ANGELA from MEBANE, NC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Error Code F1
I usually try the cheapest part to replace when I come to a fork In the road but I wasn't home at the time and my other half called in the "expert". He said it was the clock timer and it would be $450 to replace it. She sent him away and I bought one online for $200 and put it in only to find out that it didn't solve the problem. Did some reading and found out that it could be the sensor. Put an ohm meter on it and found that to be the problem. Left the new clock timer in it anyway so now we're good for another 100,000 cookies or 1000 pizzas, which ever comes first
Parts Used:
-
Jon from Little Silver, NJ
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gas oven won't light
get liquid wrench, remove oven door(2 screws) remove oven bottom(2 screws) follow directions included with part. unplug or shut off electricity at breaker panel, Have a good light source.
Parts Used:
-
James from GRASS VALLEY, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would overheat and not control properly
Simply took oven out of wall, removed back plate, unplugged old sensor, went in the front and unscrewed old sensor, put in new sensor, went in back and plugged in new sensor, put on back plate, push oven in wall. Turn on power
Parts Used:
-
Mason from WESTVILLE, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!