GDP695SSM5SS General Electric Dishwasher - Instructions

This is a replacement that is straightforward but a bit mechanical. For an experienced engineer it was no problem but for the common household this is a repair best left to the pros. Fixed the issue no problem and the dishwasher is working perfectly now.

It took a little googling and YouTubing to find the problem and solution, but once we had this UI board in hand, the installation was simple.

Most of the labor and little bit of struggle was taking the dishwasher door apart to get to the UI board.

Make sure to follow the instructions in the package to configure for your model, which was straightforward and simple enough to do.

Once the door was back together and reinstalled, she worked like a dream. The display also seems brighter to me. We haven't had the "random singing" that the dishwasher was doing before the original UI board went out either.

You can do this fix!

Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight

Process of elimination and a visit to my local repair store told me it was wise to try the tub gasket, and according to partselect.com, it solved the problem a majority of the time. My local repair dealer agreed: Try it. They agreed because for them to replace a lower door gasket AND the $10 tub gasket... if they came out, the service call and parts would equal half the cost to replace the whole dishwasher. So I bought a tub gasket from partselect.com and replaced the old one. It worked, it was easy, so if your same make & model is leaking? Try it first. That's my advice.

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked

Followed a u-tube video to remove dish wash door assembly to get to the control board . Not too hard if you are mechanically inclined.

It took longer to uninstall and reinstall the dishwasher than it did to change out the part

Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.

- Removed standing water using shopvac
- Uninstalled dishwasher
- Hooked up hoses temporarily and ran dishwasher
- Cancelled wash cycle and started drain cycle - checked drain pump voltage at pump power cable - OK
- Measured drain pump windings and verified open circuit
- Ordered new drain pump
- Removed old drain pump and installed new unit
- Hooked up hoses temporarily and ran dishwasher - OK
- Re-installed dishwasher

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

the actual gasket tub seal was easy, 10 minutes. The trim tub gaskets were a pain because I had to uninstall the dishwasher (not plumbing or electrical) then pull it out from the cabinet, remove old trim and re-install. Re-leveled dishwasher, screwed into side of cabinets but it still leaks. Can't figure out where but after replacing all the trim and gaskets its very frustrating.

took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.