GDF610PGJ5WW General Electric Dishwasher - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The soap dispenser was broken os to save money I ordered one on-line
The repair instructions were great and the repair went well. The repair took less than an hour.
Thank you
Gary
Thank you
Gary
Parts Used:
-
GARY from SOAP LAKE, WA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drain pump needed replaced
The only directions that came with the new pump and filter, was how to replace the filter. I had to find a You Tube video to show me where the drain pump was located., and the way to get to it. I also had to figure out how the new pump was hooked up electrically, since the new pump did not work with the plug in on the machine.
Parts Used:
-
Kim from BLACKFOOT, ID
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench (Adjustable)
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door gasket at bottom of door was falling apart and leaking
1. Shut off circuit breaker power
2. remove toekick
3 .disconnect door wire harness at bottom of main control board
4. release 2 wire ties securing harness to tub using long nose pliers
5. remove 2- 1/4 in. hex head screws from bottom of door
6. insert 5/32 in Allen wrench through existing holes in front leg and hinge arm when door is partially opened.(about 1/4 of the way)
7. repeat step 6 on both sides (this locks door partially open)
8. lift door up about 3 in. then tilt door in and remove door completely
9. slide old gasket out and replace with new gasket
9. reassemble door
2. remove toekick
3 .disconnect door wire harness at bottom of main control board
4. release 2 wire ties securing harness to tub using long nose pliers
5. remove 2- 1/4 in. hex head screws from bottom of door
6. insert 5/32 in Allen wrench through existing holes in front leg and hinge arm when door is partially opened.(about 1/4 of the way)
7. repeat step 6 on both sides (this locks door partially open)
8. lift door up about 3 in. then tilt door in and remove door completely
9. slide old gasket out and replace with new gasket
9. reassemble door
Parts Used:
-
Alvin from SCHENECTADY, NY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower spray arm had melted tips
-
Ed from TRAVELERS RST, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not shut, machine would not run.
Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!
Parts Used:
-
Deborah from BRADENTON, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Need New Board
-
Lauran from MYRTLE CREEK, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Socket set
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating element broke off and burned a hole in rubber tube, leaking water.
Replaced the dishwasher with a new one! used the same brand (GE) but different model to make the job a little easier, first cut power to the outlet, disconnected electrically from dishwasher, cut off water source from dishwasher, and disconnected hose from garbage disposal, removed old dishwasher put new one in, connected electrical wires (color coded), connected water supply with pliers, and connect your hose to your disposal and level your new disposal with leveling screws that comes with the new dishwasher. Put front cover plate on with screws provided with a screwdriver and that's it.
Parts Used:
-
Mario from CHESAPEAKE, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not know door was closed
Parts diagram shows Striker can be popped out with screwdriver. Not true. It has a screw bolting it internally. Impossible to get to unless you disassemble the entire door. We took a power drill and small drill bit and bore it out like a cavity in a tooth. Needle nose pliers to extract the screw. Pretend your a dentist. Fixed it in 5 minutes. Replacement fit tight. A+
Parts Used:
-
Lesa from BETHALTO, IL
-
Difficulty Level:Very Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thumping Sound during the WashRinse cycles
Chances are your Lower spray arm is worn or jets are off. Replacing this part is very easy. Grab the base of the lower spray arm, twist and pull straight up. Place the new one in and twist lock in place. Repair complete!
Parts Used:
-
Jedrino from HAWTHORNE, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not drying dishes
Installed new heater by pulling unit out of it’s cubby hole. Was able to gain access to the nuts that hold it down and make the seal, as well as the electrical connections. Re-installed. Helpful if you remove both dish baskets and utencil basket for access when installing heater.
Parts Used:
-
Paul from STEWARTSVILLE, NJ
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All 3 spray arms were stoped up.
Replaced all 3 spray arms in less than 10 minutes.The top one came in two pieces,the mounting bracket and the arm.Snap the bracket on the dishwasher first , then attach the arm to the bracket.
Parts Used:
-
Kenneth from SEBRING, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The blue colored silverware holders had broken pegs at the ends.
Removed the old assembly and put the new one in. Took about 15 seconds. Perfect replacement. This assembly is the complete basket. The color of the blue silverware holders changed to grey which is not an issue at all unless that was the reason you bought this dishwasher in the first place. ;-)
Parts Used:
-
Tom from BEND, OR
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Delivery
The part has been sitting at a FedEx place for over a week and no one answers my emails about why. This is all I get: "No scheduled delivery date available at this time."
Parts Used:
-
Michael from LANESVILLE, IN
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher was not heating up to dry
Took out the old heating assembly and installed the new one
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.
Parts Used:
-
Nicholas from CONCORD, NH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Wrench (Adjustable)
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher Leaking at bottom when running
To remove/install gasket one has to remove a Door Hinge Arm on one side. Then you can easy remove old gasket and replace. Please follow these steps when removing a hinge: https://www.youtube.com/watch?v=hTpe1dedyr8
Parts Used:
-
Mark from BURKE, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!