GDF610PGJ5WW General Electric Dishwasher - Instructions

I watched the video on how to replace the parts and it was very easy. Unplug the power cord, remove the kick plate and insulation. Remove the small square metal cover, remove the 2 screws that hold the control board plate. Unplug the wires, put the control board plate on the counter and replace the board. Then put everything back in the order that you removed it. Plug in the power cord. Very easy to fix. I ordered the door latch but didn't need it so I will just keep it as a spare. It took me less than 45 minutes to replace the part. The problem was the control board. Parts select saved me about 400.00. Thanks, John.

I watched a YouTube video that showed how to to do this. The first trick is finding the right video. This one worked best for me / my model.

https://www.youtube.com/watch?v=sesf0BS8fzM

The first few I watched were for models with the user display on the top of the door, and you have to open the dishwasher to see it. Mine shows the display on the outside. Look for the video that has a round plastic "vent" on the inside of the door. You will have to loosen it with some sort of tool in order to remove the display once you get the door taken apart. In the video, they used needle-nose pliers opened wide. My NN pliers don't open that wide, so I used two screw drivers. Pealing off the display is a bit challenging. I was afraid I was going to break the little plastic pins that hold it on. The rest is not too hard though, and it went back together quite easily, even though I did break a plastic piece that 0ne of the UI Control Board screws goes into. Oh well, now it has three screws holding it instead of four.

Opened door slid in new rack, came with wheels

Shut off power at breaker, remove two screws anchoring DW to counter top . Slide DW out far enough to access door latch, disconnect electrical wiring plug, remove two Phillips head screws, install new door latch, repeat installation in reverse order.

Don't remove the door! Unscrew the bolts at each lower corner of the door(this is how the door is attached to the hinges so it is now free). Then open the door fully and slowly pull the door toward you a few inches. This slides the door up the hinges and allows just enough room to slide the old gasket out and and slide the new one in. Then slide the door back down the hinges(pushing it away from you, back into place). Then simply close the door and reinstall the bolts at the bottom corners and all done! I watched several videos and believe me, removing the door to replace this gasket does nothing but turn and small quick repair into a large lengthy one.

Accessed YouTube video specific to my Model and replacement part.

https://youtu.be/TI8cUjy5YOE?si=3b0Dkk16WLl2e33D

As outlined above, the replacement took a first timer about 60 minutes to complete and resolved the issue.

I fixed this issue by replacing the Dishwasher Tub Gasket (PS11774412) and the gasket on the bottom of the door (PS11700870). Replacing the tub gasket is very easy and straight forward. You just pull it off and put the new one on. The door gasket was much more complicated. See the steps required for replacement below:

The * indicates the part number in the diagram I am referencing

1. Remove the Toe Kick Assembly (*759)
2. Remove screws holding dishwasher to counter and pull the dishwasher out
3. With door shut, disengage the springs on both sides from the arm hinge assemblies *800 (I did this by taking the rope off the pulley hinge *734)
4. Disconnect the wire going from the dishwasher body to the door (there are two or three supports for the wire that need to be removed for it to come free)
5. Open the door about 15 degrees and pull the door upward (only one angle will work for removing the door)
6. Place the door on its front on the ground
7. Remove the two screws (*745) that hold one of the arm hinge assemblies to the door and pull the hinge away from the door (you don't need to pull it all of the way out)
8. Pull the old gasket out to the side and install the new gasket

Standard repair process to replace UI. The piece worth noting is the strange behavior on initial install. After setting the jumpers to the correct pins for my model based on the instructions, the board would initially not respond. It was only after i change the jumpers to a setting for another model and put power on the board that i got a response. I then set the jumpers back to the pins for my model that the board began to respond normally. Its been fine since.

Thanks to this site for saving me about 150.00.This is my third repair with parts from your company. Thank you.

There was no repair -- it was a simple snap-in replacement of lower spray arm assembly. The shaft holding the lower spray arm in place is plastic so of course it broke when a utensil blocked the arm from spinning.

I appreciate the Parts Select company for enabling me to purchase a replacement part though that allows me to keep my old dishwasher working.

The dishwasher had been installed before we added 3/4 oak floor, so I could not pull the dishwasher out from under the counter. That will be a major project when the dishwasher dies.
To remove the door, I removed the two 1/4 " screws on the right and left bottom of the door. I used a box wrench since that was the only way to reach them. One had corroded due to a leak. it took some coaxing but finally came loose. The hint about opening the door 27 degrees and propping it open with two Allan wrenches through the hinge holes was very helpful. Then I lifted the door a little and gently pushed toward the counter releasing the door form the hinges. I took the door off to find a leak and found the right corner edge of the inside tub had cracked. Not sure how this happened. I cleaned and sanded the crack area and used J-B Weld to epoxy the crack. Replacing the gasket was easy. Slide out the old, slide in the new. Everything went back together smoothly. If I hadn't needed to repair the tub, the hint about opening the door all the way and sliding it out part way might have worked to change the gasket. Note. Unlike a stove door the dishwasher door is not that heavy.

I follow a YouTuber who had a semillar GE dishwasher model number. He was very helpful through the repair process.

Online instructions said to remove door. Found no need to. Only need to release one hinge by sliding door upward after removing 2 screws at bottom edge of door which releases both hinges. With door lifted just pry out old seal (it will be stuck so use a strong screwdriver). Then slide new seal in place. Lower door back down on hinge. Job done.

The dishwasher was not heating anymore. I suspected it was the float/flood switch, so I got that ordered. I went ahead and ordered the element also and I'm glad I did! Even though the element was good, when I tested it I loosened the nut holding the element in. When I retightened it there was NO WAY for me to get it watertight again and it kept dripping out the bottom. Mine was made in 2019, and the gaskets on the element that came with it were a terrible design - the metal flange on the element was about as big as the hole in the middle of the gasket so water just leaked between the gasket "donut" hole and the element with no way to seal. The element I bought for this repair just in case had a totally redesigned gasket that sealed right up and didn't have the same design issue. So beware, if you are fiddling with the element in your process, be sure the gasket will reseal - or just have an extra new element in case it is the old (bad) design.

The flood switch was easy to find (with dishwasher on its back) in a white housing under the black circular sump.

Getting the actual switch out of that housing took some doing. I ended up using 4 small kebab sticks - toothpicks might work better- all 4 tabs have to be pulled out at the same time.

So I ended up changing out both the element (which was good but started leaking) and the float switch.

IMPORTANT!!! Before you put the dishwasher back in, you probably need to reset the thermal cutoff (TCO) on the back of the dishwasher. Follow the wire up from the element and it is the first thing it goes to. There should be a small (3mm) black button that has popped out. Press that back in. With your repair (float switch or element) it should start heating again - at least mine did.

I removed the old gasket and installed the new one in the same position as the one I removed. I had to feel with my fingers for the ridge to insert the gasket so that it would hold. I must admit that I was skeptical that it would work (the old one didn't even seem very damaged). I ran a cycle and there was no more leaking. We've been using the dishwasher ever since with no issues of leakage.

Very satisfied customer.