GDF520PGD0WW General Electric Dishwasher - Instructions

took out old and replaced with new

1) Pull out lower basket plate holder out. Now would be a good time to check roller wheels. 2) Grasp lower spray arm base (knurled collar on base) and turn counter clockwise to release. 3) Install new spray arm and turn knurled collar on base clockwise to lock it in. 4) Reinstall lower basket plate holder.
* Done *

Opened the door, put arm on bottom, slid in and twisted. Very, very easy. The right part means a lot. Thank you very much. “ Ol Stump”.

Unscrewed brackets on top of dishwasher from underside of counter. Removed dress plate at bottom of dishwasher. Pulled dishwasher out of opening to access door hinge. Disconnected pulley cable/rope from each side door hinge. Let go slowly.
There is a 1/4 bolt holding the door tight to the hinge. With door closed (still) the screw is on bottom of bottom edge. Use wrench to loosen and remove.
Once both bolts are out, open door. Pull door away from dishwasher just enough (1-3 inches) to slide out old gasket. Prior to removing take note of existing gasket orientation and installation. Slide old gasket out one side and slide new gasket in.
Push in door tight to hinges,close door, use wrench to put bolts back in. Reattach pulley cable/rope to each side. Push back into opening. Reattach to counter. Put dress plate on bottom back.
Return dishwasher to regular use.

Simply pick the basket up to slide wheels onto axles and push in until they lock in place.

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.

Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.

Replaced latch

Shut Power off at Circuit Breaker
1. Remove Kick Plate & Insulation
2. Unplug electrical connection from door to unit
2. Remove 2 screws with nut driver to release panel above electrical connection box
3. Pull panel down and out to expose board
4. Disconnect 3 plugged wire leads
5. replace old board with the new in the tray
6. Plug connectors in
7. Put unit back together

Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.

Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one

2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.

Simply pulled the new one out of the box and put it into the dishwasher.

The main board is located under the washer in metal box accessed by removal of front plate at bottom. Removal of 2 screws on front of metal box allows board to drop down. However, very cumbersome to work on your back on floor in small space. I took the easy way and slid the washer out of cabinet, then turned washer ( it's light weight) on its back to access & remove old board and easily replace with new one. Also one of the connector plugs had to be replaced wired into the power connection made me very glad I was not working on my back ! Then simply turn washer upright and slide back into its cubby hole under counter.

took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.

Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.