EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
Back
Back
Keep typing for more specific results...
Models > FGHS2631PP4A > Instructions

FGHS2631PP4A Frigidaire Refrigerator - Instructions

All Instructions for the FGHS2631PP4A
61 - 75 of 631
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Temperature readout segments no display, selection for water would not illuminate.
1. Removed power from refridgerator. Removed two Phillips screws holding trim panel on. This gave access to two Phillips screws holding control board touch pad assembly in place. Removed two screws and control board. Unplugged 4 small connectors on old control board and installed new control board by plugging in connectors and reinstalled in refridgerator. Plugged in fridge to power. Success!
Parts Used:
USER INTERFACE
  • Danny from TITUSVILLE, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
11 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
you r label (this end in arrow is wrong
placed filter in sideways
Parts Used:
Refrigerator Air Filter
  • melvin from BASKING RIDGE, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
15 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Crisper support was broke
Parts Supply had a YouTube video to show it was done. This is one of the best sites to get parts there is. Easy to use, tells you how to install them easily. Thanks Parts Supply, I'll be back whenever I need a appliance part.
Parts Used:
Front Crisper Cover Support Door Shelf
  • Ray from Millbrook, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
11 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice make does not fill with water
I replaced the water valve, but it still did not fix the problem.The old water valve I took out I'm assuming worked fine, I think the real problem is ice building up in pipe or some other blockage.

Parts select was very fast in shipping, very positive experience with them.
I will definitely purchase again from this site.
Parts Used:
Refrigerator Water Inlet Valve
  • Amritpal from sacramento, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set, Wrench set
12 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Failed icemaker
First I loosened the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...re-installed the new icemaker first attaching the wires and then fitting over the screw holders and tightened the screws. That was it!
Parts Used:
Rearmount Ice Maker Assembly
  • Jay from St louis, MO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
11 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking from back of refrigerator
Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!
Parts Used:
Refrigerator Water Inlet Valve
  • Barbara from Bryan, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
12 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
housing-crusher was broken
removed ice maker box and disassembled crusher unit on front of box and installed new housing.
Parts Used:
Dispenser Crusher Housing
  • Bob from Milton, WV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
12 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
worn out gasket...
very easy to install...shipping was really fast...i would order to this website again....
Parts Used:
GASKET-REFR DOOR,GRAY,MAGNETIC
  • Yves from Miramar, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
12 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water valve failure
removed rear cover, removed screws, diconnected water line connections, cut off old water line connection, installed new compression water line connection, replace screws in water line housing, replace rear cover.

worked fine
Parts Used:
Refrigerator Water Inlet Valve
  • Robert from Louisville, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
13 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door didn't seal good
Pulling the old seal was the easy part. The problem became dificult when I opened the seal package. Either Part Select or UPS had folded the seal in half. Witch caused the wire inside the seal to become crimped up. I used a pair of pliers "carefully" to straighten the wire as best I could. Luckly it worked, after pressing it firmly all the way aroud about 5 or 6 times. I'll still keep an eye on it for the next couple of weeks.
Parts Used:
GASKET-REFR DOOR,GRAY,MAGNETIC
  • jerimy from greenbrier, TN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
crisper drawer supports broke
The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.
Parts Used:
Light Bulb Rear Crisper Support
  • Timothy C. from Aberdeen, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
20 of 43 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice maker motor shorted out
loosen 2 screws
unplug connector
remove
replug
replace
tighten 2 screws
done
Parts Used:
Rearmount Ice Maker Assembly
  • Robert from DeFuniak Spgs, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor falure of evaporator fan
removed fan unit from frig and installed new motor and then replaced back in frig. No tools needed. need to unplug unit and take apart and put new motor in the unit and then plug back in.
Parts Used:
MOTOR,EVAPORATOR FAN
  • john from Concho, AZ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
18 of 38 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The drum ice maker broke in half so it couldn't dependent the ice.
I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.
Parts Used:
Ice Dispenser Drum
  • ROWENA from WIGGINS, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken door shelf bin
put the new ones
Parts Used:
Door Shelf
  • Raul from Kissimmmee, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FGHS2631PP4A
61 - 75 of 631