EGR2000EM3CC General Electric Range - Instructions

I deturmined that the flame starter was not pulling enough amps to open the gas valve (safety valve) . pulled two hand screws and removed floor of oven exposing the flame bar and flame starter. removed two screws on flame starter. removed lower pan drawer and disconected the electrical plug for flame starter. replaced in reverse order. easy.

I found that it was a little easier to pull out the stove to do the electrical connections. First I pulled out the stove being very careful not to bend the gas line. I pulled out the wires and disconnected them. I removed the 2 screws that hold the igniter and compared it to the new one it matched. I hooked it back up with the 2 screws then did the wire connections pushed the stove back carefully and tested the new igniter it worked like new no more microwave dinners thanks parts select .com

had to take back off of oven because of the connector and the plug end insert had the wrong pin so i had to take it apart and use old ones then i put the assembly in /and put oven back together

I turned the gas off and disconnected the stove & unplugged it from electricity. Pulled the stove out & removed the part. I ordered the regulator from PartSelect and it arrived promptly in 2 days. I replaced the Kit-Valve & Regulator with no problem. I changed the orfice jet from natural gas to butane. It works well.

remove the door,racks,cover over burner,burner,element,replaced element and rest in reversed order.

First I removed the botoom drawer.
Second, removed three 1/4 in (head size) screws and removed the reflector pan from the bottom of the oven.
Third I removed the three racks in the main part of the oven and then the two slot head screws that retain the oven floor. I then removed the oven floor.
Four, now that I had access to the ignitor, I removed the two 1/4 (head size) screws that mounted the ignitor to the burner.
Fifth I disconnected the wire plug which is located in the lower section of the oven. I was unable to route the wire with it's connector on out of the oven, so I just snipped the wires and took it out in two pieces.
Installation was just the reversal of this with the obvious exception of snipping the wires. I was able to route the wires differently so that I did not have to pass the connector behind any restrictions.
Finally afte all was reassembled, I did an ops check and everything worked just fine.

To get to the element I had to remove the lower cover from inside the oven.

After that I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. The wires are accessible from behind the undertray.

Installation of the new one was simply the reverse.

Before re-installing the burner cover I did a quick test to ensure the new igniter functioned properly and that I hadn't mis-diagnosed the problem. The element quickly started to glow and that was it.

The oven now works as it should.

Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.

After getting the metric set at Harbor Freight the removal and install was easy. Having an extra set of hands is helpful.

Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie

Took 5 minutes to repair easy peasy??

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plastic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.

Start by shutting off the main gas supply to the range and unplugging the electric cord.
You will first need to take the plastic control knobs of from each individual burner (they should slide straight off).
Next, you will need to remove two phillips head screws on the front face of the panel. They are located on the right side of each rear valve burner stem that is sticking out through the panel.
Next, open the oven door, locate and remove the three screws on the bottom of the front face panel. The front panel should now come off exposing the top burner manifold and all of the valve burners.
The next step would be to take the burner grates and each round burner cover off (no tools required). This will expose the top of each individual burner. You will see screws that hold each individual burner down to the stove top. On my stove the heads were all rusted and I could not remove them. If you can remove all four of your burners and disconnect the wire on each ignitor and set the burners aside.
Next, go back to the front of the stove where you took off the panel and you will see two metal clips on each side of the stove top. Push each one of these in with a screwdriver and gently lift up on the stove top. It should hinge up towards the back of the stove and give you full access to the burner valve you need to change.
Next, use a box end wrench (I think it was 1/2") and remove the gas line attached to the burner valve. After the gas line is removed, take out the bolt and clamp that holds the burner valve to the manifold. The old valve should drop out.
Install the new valve making sure the rubber gasket is seated properly, reattach the clamp and bolt and reinstall the burner tube line.
Before you put the range all back together turn the gas back on at the appliance shutoff. Locate the gas orifice for that particular burner and hold your thumb or finger over the hole. Turn on the burner and leak test the burner tube connection and where the valve is clamped into the manifold.
Shut the burner back off if the leak test passes and reassemble the stove.
If your burners won't come out of the stove because the screw heads are rusted off (like mine was), you can carefully lift the lid a couple of inches to gain access to the valve. Make sure you don't bend or kink any of the burner tubes.

Opened the back and installed the new one. The only problem was pealing the paper of the old one that shows the labels. Strongly recommend to buy that part also. The job will be more neat.